Cisco Cisco TelePresence MX700 Manual De Manutenção
D15331.01 MX700 and MX800 Administrator Guide CE8.0, NOVEMBER 2015.
www.cisco.com — Copyright © 2015 Cisco Systems, Inc. All rights reserved.
95
Cisco TelePresence MX700 and MX800
Administrator Guide
Conference DefaultCall Protocol
Define the Default Call Protocol to be used when placing calls from the system.
Requires user role: ADMIN
Default value: Auto
Default value: Auto
Value space: Auto/H323/Sip/H320
Auto: Enables auto-selection of the call protocol based on which protocols are available.
If multiple protocols are available, the order of priority is: 1) SIP; 2) H323; 3) H320. If the
system cannot register, or the call protocol is not enabled, the auto-selection chooses
H323.
H323: All calls are set up as H.323 calls.
Sip: All calls are set up as SIP calls.
H320: All calls are set up as H.320 calls (only applicable if connected to Cisco
H323: All calls are set up as H.323 calls.
Sip: All calls are set up as SIP calls.
H320: All calls are set up as H.320 calls (only applicable if connected to Cisco
TelePresence ISDN Link).
Conference DefaultCall Rate
Define the Default Call Rate to be used when placing calls from the system.
Requires user role: ADMIN
Default value: 1920
Default value: 1920
Value space: Integer (64..6000)
Set the default call rate (kbps).
Conference DoNotDisturb DefaultTimeout
This setting determines the default duration of a Do Not Disturb session, i.e. the period
when incoming calls are rejected and registered as missed calls. The session can be
terminated earlier by using the user interface (Touch controller). The default value is 60
minutes.
Requires user role: ADMIN
Default value: 60
Default value: 60
Value space: Integer (0..1440)
Set the number of minutes (between 0 and 1440, i.e. 24 hours) before the Do Not
Disturb session times out automatically.
Conference Encryption Mode
Define the conference encryption mode. A padlock with the text "Encryption On" or
"Encryption Off" displays on screen for a few seconds when the conference starts.
NOTE: If the Encryption Option Key is not installed on the video system, the encryption
NOTE: If the Encryption Option Key is not installed on the video system, the encryption
mode is always Off.
Requires user role: ADMIN
Default value: BestEffort
Default value: BestEffort
Value space: Off/On/BestEffort
Off: The system will not use encryption.
On: The system will only allow calls that are encrypted.
BestEffort: The system will use encryption whenever possible.
> In Point to point calls: If the far end system supports encryption (AES-128), the call will
On: The system will only allow calls that are encrypted.
BestEffort: The system will use encryption whenever possible.
> In Point to point calls: If the far end system supports encryption (AES-128), the call will
be encrypted. If not, the call will proceed without encryption.
> In MultiSite calls: In order to have encrypted MultiSite conferences, all sites must
> In MultiSite calls: In order to have encrypted MultiSite conferences, all sites must
support encryption. If not, the conference will be unencrypted.
Conference FarEndControl Mode
Lets you decide if the remote side (far end) should be allowed to select your video sources
and control your local camera (pan, tilt, zoom).
Requires user role: ADMIN
Default value: On
Default value: On
Value space: Off/On
Off: The far end is not allowed to select your video sources or to control your local
camera (pan, tilt, zoom).
On: Allows the far end to be able to select your video sources and control your local
On: Allows the far end to be able to select your video sources and control your local
camera (pan, tilt, zoom). You will still be able to control your camera and select your
video sources as normal.
Introduction
Configuration
Peripherals
Maintenance
System settings
Appendices
System settings