Cisco Cisco IOS Software Release 12.0(21)S1
1-Port Channelized OC-48/STM-16 ISE and 4-Port Channelized OC-12/STM-4 ISE Line Cards for the Cisco 12000 Series
Configuring BER Testing
39
1-Port Channelized OC-48/STM-16 ISE and 4-Port Channelized OC-12/STM-4 ISE Line Cards for the Cisco 12000 Series Router
Cisco IOS Release 12.0(33)S4
router#show controller provision 5
Slot 5 :CH-OC48-X, GULF Revision:4, Dynamic Provisioning:disabled
'microcode reload' required:No
Interface POS5/0:1 : activated
Interface Serial5/0.2:1 : activated
Interface Serial5/0.2:2 : activated
Interface Serial5/0.2:3 : activated
Interface POS5/0:5 : activated
Interface Serial5/0.9:1 : activated
Interface Serial5/0.9:2 : activated
Interface Serial5/0.9:3 : activated
router # configure terminal
router(config)# interface pos 5/0:1
router(config-if)# ip address 10.0.1.1 255.255.255.0
router(config-if)# no shutdown
router(config)# interface pos 5/0:5
router(config-if)# ip address 10.0.5.1 255.255.255.0
router(config-if)# no shutdown
router(config-if)# interface pos 5/0.2:1
router(config-if)# ip address 10.0.21.1 255.255.255.0
router(config-if)# no shutdown
router(config-if)# interface pos 5/0.2:2
router(config-if)# ip address 10.0.22.1 255.255.255.0
router(config-if)# no shutdown
router(config-if)# interface serial 5/0.2:3
router(config-if)# ip address 10.0.23.1 255.255.255.0
router(config-if)# no shutdown
router(config-if)# interface serial 5/0.9:1
router(config-if)# ip address 10.0.91.1 255.255.255.0
router(config-if)# no shutdown
router(config-if)# interface serial 5/0.9:2
router(config-if)# ip address 10.0.92.1 255.255.255.0
router(config-if)# no shutdown
router(config-if)# interface serial 5/0.9:3
router(config-if)# ip address 10.0.93.1 255.255.255.0
router(config-if)# no shutdown
router(config-if)# exit
router#
Configuring BER Testing
Bit error rate test (BERT) circuitry is built into the 1-Port Channelized OC-48/STM-16 ISE and 4-Port
Channelized OC-12/STM-4 ISE line cards. There is one pseudorandom binary sequence generator every
16 channels. For each group of 16 channels, BER testing can be run on only one interface at a time.
Channelized OC-12/STM-4 ISE line cards. There is one pseudorandom binary sequence generator every
16 channels. For each group of 16 channels, BER testing can be run on only one interface at a time.
You can set one local DS3/E3 serial port to BERT mode while the remaining local serial ports continue
to transmit and receive normal traffic. A BER test checks communication between the local and the
remote DS3/E3 ports.
to transmit and receive normal traffic. A BER test checks communication between the local and the
remote DS3/E3 ports.
If traffic is not being transmitted or received, create a back-to-back loopback BER test and send out a
predictable stream to ensure that you receive the same data that was transmitted.
predictable stream to ensure that you receive the same data that was transmitted.
To determine if the remote DS3/E3 serial port returns the BERT pattern unchanged, the system
administrator for the remote router must manually enable network loopback at the remote DS3/E3 serial
port, while you enter a bert pattern interface configuration command for specified time intervals on the
local DS3/E3 serial port.
administrator for the remote router must manually enable network loopback at the remote DS3/E3 serial
port, while you enter a bert pattern interface configuration command for specified time intervals on the
local DS3/E3 serial port.
With BER tests, you can accurately assess the number of errors on a DS3/E3 link and diagnose signal
problems in the field.
problems in the field.