Cisco Cisco 2106 Wireless LAN Controller
12
Release Notes for Cisco Wireless LAN Controllers and Lightweight Access Points for Release 4.2.205.0
OL-31336-01
Important Notes
New 1250 series access points shipped from the factory contain new bootloader images, which fixes the
flash file system after it is corrupted during a crash (without losing files). This new bootloader
automatically sets a new CRASH_LOG environment variable to “yes,” which enables a crash log to be
generated following a crash but only on controllers running software release 4.2.112.0 or later.
Therefore, no user configuration is needed to enable a crash log on new 1250 series access points shipped
from the factory.
flash file system after it is corrupted during a crash (without losing files). This new bootloader
automatically sets a new CRASH_LOG environment variable to “yes,” which enables a crash log to be
generated following a crash but only on controllers running software release 4.2.112.0 or later.
Therefore, no user configuration is needed to enable a crash log on new 1250 series access points shipped
from the factory.
These examples show the output from the CLI commands (in bold) that you use to check the bootloader
version on LWAPP and autonomous 1250 series access points:
version on LWAPP and autonomous 1250 series access points:
LWAPP (commands entered on the controller CLI):
(wlc) >debug ap enable AP001b.d513.1754
(wlc) >debug ap command "show version | include BOOTLDR" AP001b.d513.1754
(wlc) >Thu Apr 23 09:31:38 2009: AP001b.d513.1754: BOOTLDR: C1250 Boot Loader
(C1250-BOOT-M) Version 12.4(10b)JA, RELEASE SOFTWARE (fc1)
Autonomous (command entered on the access point CLI):
ap# show version | include BOOTLDR
BOOTLDR: C1250 Boot Loader (C1250-BOOT-M) Version 12.4(10b)JA, RELEASE SOFTWARE (fc1)
Port Mirroring Not Supported on Some Controller Platforms
The controller Port Mirroring feature is not supported on 2100 series controllers, 4400 series controllers,
Cisco WiSM controllers, and Wireless LAN Controller Network Modules.
Cisco WiSM controllers, and Wireless LAN Controller Network Modules.
RLDP Limitations in This Release
Rogue Location Discovery Protocol (RLDP) is a controller feature that detects the presence of rogue
access points that are connected to your wired network. In this software release, RLDP operates with
these limitations:
access points that are connected to your wired network. In this software release, RLDP operates with
these limitations:
•
RLDP detects rogue access points that are configured for open authentication.
•
RLDP detects rogue AP which use a broadcast BSSID--that is, the access point broadcasts its SSID
in beacons.
in beacons.
•
RLDP detects only rogue AP that are on the same the network. In other words, if an access list in
the network prevents the sending of RLDP traffic from the rogue AP to the controller, RLDP will
not work.
the network prevents the sending of RLDP traffic from the rogue AP to the controller, RLDP will
not work.
•
RLDP does not work on 5-GHz DFS channels.
•
RLDP is a best-effort protocol. For each rogue, the controller initiates RLDP only once. If the
controller does not detect a rogue (due to a noisy RF environment, for example), the controller does
not retry. However, you can initiate RLDP manually on a rogue at any time.
controller does not detect a rogue (due to a noisy RF environment, for example), the controller does
not retry. However, you can initiate RLDP manually on a rogue at any time.
Configuration File Stored in XML Format
In controller software 4.2, the controller’s bootup configuration file is stored in an Extensible Markup
Language (XML) format rather than in binary format. Therefore, you cannot download a binary
configuration file onto a controller running software release 4.2. However, when you upgrade a
controller from a previous software release to 4.2, the configuration file is migrated and converted to
XML.
Language (XML) format rather than in binary format. Therefore, you cannot download a binary
configuration file onto a controller running software release 4.2. However, when you upgrade a
controller from a previous software release to 4.2, the configuration file is migrated and converted to
XML.