Cisco Cisco 2106 Wireless LAN Controller
14
Release Notes for Cisco Wireless LAN Controllers and Lightweight Access Points for Release 4.2.173.0
OL-31336-01
Important Notes
Note
Daylight Savings Time (DST) is not supported in controller software release 4.2.
UNII-2 Channels Disabled on New 1000 Series Access Points for United States,
Canada, and Philippines
Canada, and Philippines
New Cisco 1000 series lightweight access points for the United States, Canada, and the Philippines do
not support the UNII-2 band (5.25 to 5.35 GHz). These models are labeled AP10x0-B, where “B”
represents a new regulatory domain that replaces the previous “A” domain.
not support the UNII-2 band (5.25 to 5.35 GHz). These models are labeled AP10x0-B, where “B”
represents a new regulatory domain that replaces the previous “A” domain.
FCC DFS Support on 1130 Series Access Points
Federal Communications Commission (FCC) dynamic frequency selection (DFS) is supported only on
1130 series access points in the United States, Canada, and the Philippines that have a new FCC ID.
Access points use DFS to detect radar signals such as military and weather sources and then switch
channels to avoid interfering with them. 1130 series access points with FCC DFS support have an FCC
ID LDK102054E sticker. 1130 series access points without FCC DFS support have an LDK102054 (no
E suffix) sticker. 1130 series access points that are operating in the United States, Canada, or the
Philippines; have an FCC ID E sticker; and are running the 4.1.171.0 software release or later can use
channels 100 through 140 in the UNII-2 band.
1130 series access points in the United States, Canada, and the Philippines that have a new FCC ID.
Access points use DFS to detect radar signals such as military and weather sources and then switch
channels to avoid interfering with them. 1130 series access points with FCC DFS support have an FCC
ID LDK102054E sticker. 1130 series access points without FCC DFS support have an LDK102054 (no
E suffix) sticker. 1130 series access points that are operating in the United States, Canada, or the
Philippines; have an FCC ID E sticker; and are running the 4.1.171.0 software release or later can use
channels 100 through 140 in the UNII-2 band.
Inaccurate Transmit Power Display
After you change the position of the 802.11a radio antenna for a lightweight 1200 or 1230 series access
point, the power setting is not updated in the controller GUI and CLI. Regardless of the user display, the
internal data is updated, and the transmit power output is changed accordingly. To see the correct
transmit power display values, reboot the access point after changing the antenna’s position.
(CSCsf02280)
point, the power setting is not updated in the controller GUI and CLI. Regardless of the user display, the
internal data is updated, and the transmit power output is changed accordingly. To see the correct
transmit power display values, reboot the access point after changing the antenna’s position.
(CSCsf02280)
Setting the Retransmit Timeout Value for TACACS+ Servers
Cisco recommends that the retransmit timeout value for TACACS+ authentication, authorization, and
accounting servers be increased if you experience repeated reauthentication attempts or the controller
falls back to the backup server when the primary server is active and reachable. The default retransmit
timeout value is 2 seconds and can be increased to a maximum of 30 seconds.
accounting servers be increased if you experience repeated reauthentication attempts or the controller
falls back to the backup server when the primary server is active and reachable. The default retransmit
timeout value is 2 seconds and can be increased to a maximum of 30 seconds.
Configuring an Access Point’s Prestandard Power Setting
An access point can be powered by a Cisco prestandard 15-watt switch with Power over Ethernet (PoE)
by entering this command:
by entering this command:
config ap power pre-standard {enable | disable} {all | Cisco_AP}