Cisco Cisco 2000 Series Wireless LAN Controller
28
Release Notes for Cisco Wireless LAN Controllers and Cisco Aironet Lightweight Access Points for Releases 3.2.78.4 and 3.2.78.0
OL-31336-01
Caveats
•
CSCsb752843—Corrected the WiSM GUI Monitor page to remove the incorrect model type
displayed for WiSM.
displayed for WiSM.
•
CSCsb76113—The SRAM UPM timing was corrected.
•
CSCsb76240—The phone support variable is now initialized before doing ‘or’ and ‘and’ operations.
•
CSCsb76710—The correct QBSS value is reported for element 11 / length 4 and element 221.
•
CSCsb77161—The Cisco Aironet 1500 series lightweight outdoor access point receiver saturation
performance has been improved to comply with the IEEE 802.11 maximum receiver saturation
specification. Cisco Aironet 1500 series lightweight outdoor access points can now be placed as
close as 33 feet apart without experiencing increased packet error rate and without turning down the
transmitter power.
performance has been improved to comply with the IEEE 802.11 maximum receiver saturation
specification. Cisco Aironet 1500 series lightweight outdoor access points can now be placed as
close as 33 feet apart without experiencing increased packet error rate and without turning down the
transmitter power.
•
CSCsb77410—Corrected the show interface detailed command response to display LAG and 29
when a LAG is enabled.
when a LAG is enabled.
•
CSCsb77487—Updated LAG debug messages.
•
CSCsb77493—Corrected the message log so that when the service port is disconnected, the wireless
LAN controller no longer detects network loop messages.
LAN controller no longer detects network loop messages.
•
CSCsb77761—No longer receiving frame length out of bounds error messages on the CLI console.
•
CSCsb77881—The idle timeout now works on REAP Cisco lightweight access points.
•
CSCsb78726—Corrected the code so L2TP debugs no longer show passwords in clear text.
•
CSCsb78891—Cisco 4400 Series Wireless LAN Controllers equipped with a VPN Termination
Module no longer reset after hosting an IPSec client for some hours.
Module no longer reset after hosting an IPSec client for some hours.
•
CSCsb79228—Multicast is now working on the second Cisco 4400 Series Wireless LAN Controller
NPU.
NPU.
•
CSCsb79267—The LAG option can no longer be disabled for those platforms, such as the WiSM,
in which the LAG is not optional.
in which the LAG is not optional.
•
CSCsb79282—The show lag port hash output now matches the actual port numbering.
•
CSCsb79395—The LAG function no longer experiences an interface initialization error.
•
CSCsb80402—Cisco 2000 Series Wireless LAN Controllers now prompt with an error message
when running the install script.
when running the install script.
•
CSCsb80561—Cisco lightweight access points now join a wireless LAN controller after they reset.
•
CSCsb80695—The Cisco logo no longer appears on NEC branded interfaces.
•
CSCsb81759—Made changes to the WiSM dynamic SDRAM configuration to support future
memory modules.
memory modules.
•
CSCsb82767—Updated the session timeout to work correctly with webauth.
•
CSCsb8286—During bootup the WiSM no longer generates a bad CRC error.
•
CSCsb83130—Cisco 2000 Series Wireless LAN Controllers no longer send web auth client DNS
queries out over the management port instead of over the client's dynamic interface before client
authentication.
queries out over the management port instead of over the client's dynamic interface before client
authentication.
•
CSCsb83539—The Controller > General web interface page configuration entries can now be
changed.
changed.
•
CSCsb83552—The web interface now shows the mobility anchor IP addresses in the WLAN
Mobility Anchors page.
Mobility Anchors page.
•
CSCsb84030—The wireless LAN controllers no longer display VLAN modify error messages when
booting.
booting.