Cisco Cisco 4402 Wireless LAN Controller

To check the setting of the boot variable, do the following:

On the controller, enter the following commands for each mesh access point (MAP):

debug ap enable AP_Name

debug ap command "more flash:/env_vars" Cisco_AP

A display similar to the following appears:

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: 5G_RADIO_CARRIER_SET=0020

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: 5G_RADIO_ENCRYPTION_CONFIG=02

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: 5G_RADIO_MAX_TX_POWER=65535

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: 

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: DEFAULT_ROUTER=11.200.9.20

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: DEVIATION_NUM=0

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: DOT11G_RADIO_MODE=255

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: DOT11_DEVICE_TYPE=4C

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: DOT11_ENCRYPTION_CONFIG=02

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: DOT11_MAX_ASSOCIATION_NUM=2007

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: ENABLE_BREAK=yes

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: FAB_PART_NUM=800-28909-02

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: IP_ADDR=11.200.9.99

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: MAC_ADDR=00:1d:e5:e8:aa:00

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: MAC_ADDR_BLOCK_SIZE=256

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: MANUAL_BOOT=no

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: NETMASK=255.255.0.0

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: NEW_IMAGE=yes

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: PCA_ASSY_NUM_800=03 20 00 70 ED 02

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: PCA_PART_NUM_73=49 2A A6 02

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: PCA_REVISION_NUM=A0

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: PCA_REVISION_NUM_800=A0

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: PCB_SERIAL_NUM=FHH1101007F

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: PEP_PRODUCT_ID=AIR-LAP1521AG-A-K9

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: PEP_VERSION_ID=V01

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: PRODUCT_MODEL_NUM=AIR-LAP1521AG-A-K9

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: RADIO_CARRIER_SET=00FF

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: RADIO_MAX_TX_POWER=65535

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: SYSTEM_REVISION_NUM_800=A0

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: TOP_ASSY_NUM_800=03 20 00 71 22 02

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: TOP_ASSY_SERIAL_NUM=SJC1101007F

Tue Jan 15 00:00:15 2009: SLT-HCAB-MAP-01-fe.bb.6f: param-any=

To turn off debug access, enter debug ap disable AP_Name.

You do not need to turn off the debug access at this point if a boot update is required. Continue 
to the 

.