Cisco Cisco Packet Data Gateway (PDG) Documentation Roadmaps
ST16 Hardware Platform Overview
Application and Line Cards ▀
Cisco ASR 5000 Series Product Overview ▄
OL-22937-01
Ethernet 1000 (Gigabit Ethernet) Line Cards
The Ethernet 1000 line card is commonly referred to as the GigE or Gigabit Ethernet Line Card (GELC). The Ethernet
1000 line card is installed directly behind its respective PAC, providing network connectivity to the packet data
network. The type of interfaces for the Ethernet 1000 line cards is dictated by the Small Form-factor Pluggable (SFP)
module installed as described below:
1000 line card is installed directly behind its respective PAC, providing network connectivity to the packet data
network. The type of interfaces for the Ethernet 1000 line cards is dictated by the Small Form-factor Pluggable (SFP)
module installed as described below:
Table 14. SFP Modules Supported by the Ethernet 1000 Line Cards
Module
Type
Type
Card
Identification
Identification
Interface Type
Cable Specifications
1000Base-
SX
SX
Ethernet 1000
SX
SX
Fiber, LC
duplex female
connector
duplex female
connector
Fiber Type: Multi-mode fiber (MMF), 850 nm wavelengthCore Size
(microns)/Range:62.5/902.23 feet (275 meters)50/1640.42 feet (500
meters)Minimum Tx Power: -9.5 dBmRx Sensitivity: -17 dBmPlease read all
the notices and warnings for Class 1 Laser devices following this table before
handling this component.
(microns)/Range:62.5/902.23 feet (275 meters)50/1640.42 feet (500
meters)Minimum Tx Power: -9.5 dBmRx Sensitivity: -17 dBmPlease read all
the notices and warnings for Class 1 Laser devices following this table before
handling this component.
1000Base-
LX
LX
Ethernet 1000
LX
LX
Fiber, LC
duplex female
connector
duplex female
connector
Fiber Type: Single-mode fiber (SMF), 1310 nm wavelengthCore Size
(microns)/Range: 9/32808.4 feet (10 Kilometers)Minimum Tx Power: -9.5
dBmRx Sensitivity: -19 dBmPlease read all the notices and warnings for Class 1
Laser devices following this table before handling this component.
(microns)/Range: 9/32808.4 feet (10 Kilometers)Minimum Tx Power: -9.5
dBmRx Sensitivity: -19 dBmPlease read all the notices and warnings for Class 1
Laser devices following this table before handling this component.
1000Base-
T
T
Ethernet 1000
Copper
Copper
RJ-45
Operates in full-duplex up to 100 meters of CAT-5 Shielded Twisted Pair (STP)
cable with BER less than 10e-10.Use shielded cabling whenever possible to
further protect the chassis and its installed components from ESD or other
transient voltage damage.
cable with BER less than 10e-10.Use shielded cabling whenever possible to
further protect the chassis and its installed components from ESD or other
transient voltage damage.
Important:
Class 1 Laser Compliance Notice This product has been tested and found to comply with the limits
for Class 1 laser devices for IEC825, EN60825, and 21CFR1040 specifications.
Important:
Disposal of this product should be performed in accordance with all national laws and regulations.
The Ethernet 1000 Line Cards can be installed in chassis slots 17 through 23, 26 through 39, and 42 through 48. These
cards are always installed directly behind their respective PACs, but they are not required behind any redundant PACs
(those operating in Standby mode).
cards are always installed directly behind their respective PACs, but they are not required behind any redundant PACs
(those operating in Standby mode).
The following shows the panel of the Ethernet 1000 line card with the fiber connector, identifying its interfaces and
major components.
major components.
Figure 25. Ethernet 1000 Line Card
../../../GRAPHICS/Production/ST-series_Hardware/ST-series_LCGE_callout.wmf
General Application and Line Card Information