Cisco Cisco Content Acquirer Application
7
Release Notes for Cisco Internet Streamer CDS 2.5.7
OL-20688-02
Limitations and Restrictions
Limitations and Restrictions
This release contains the following limitations and restrictions:
•
There is a 4 KB maximum limit for HTTP request headers. This has been added to prevent
client-side attacks, including overflowing buffers in the Web Engine.
client-side attacks, including overflowing buffers in the Web Engine.
•
There is no network address translation (NAT) device separating the CDEs from one another.
•
Do not run the CDE with the cover off. This disrupts the fan air flow and causes overheating.
Note
The CDS does not support network address translation (NAT) configuration, where one or more CDEs
are behind the NAT device or firewall. The workaround for this, if your CDS network is behind a
firewall, is to configure each internal and external IP address pair with the same IP address.
are behind the NAT device or firewall. The workaround for this, if your CDS network is behind a
firewall, is to configure each internal and external IP address pair with the same IP address.
The CDS does support clients that are behind a NAT device or firewall that have shared external IP
addresses. In other words, there could be a firewall between the CDS network and the client device.
However, the NAT device or firewall must support RTP/RTSP.
addresses. In other words, there could be a firewall between the CDS network and the client device.
However, the NAT device or firewall must support RTP/RTSP.
Note
In Release 2.5.7, configuring Replication Bandwidth Scheduling is only supported on a per SE-basis;
Device Group configuration of Replication Bandwidth Scheduling is not supported.
Device Group configuration of Replication Bandwidth Scheduling is not supported.
Important Notes
To maximize the content delivery performance of a CDE200, CDE205, or CDE220, we recommend you
do the following:
do the following:
1.
Use port channel for all client-facing traffic.
Configure interfaces on the quad-port gigabit Ethernet cards into a single port-bonding interface.
Use this bonding channel, which provides instantaneous failover between ports, for all client-facing
traffic. Use interfaces number 1 and 2 (the two on-board Ethernet ports) for intra-CDS traffic, such
as management traffic, and configure these two interfaces either as standby or port-channel mode.
Refer to the Cisco Internet Streamer CDS 2.4 Software Configuration Guide for detailed instruction.
Use this bonding channel, which provides instantaneous failover between ports, for all client-facing
traffic. Use interfaces number 1 and 2 (the two on-board Ethernet ports) for intra-CDS traffic, such
as management traffic, and configure these two interfaces either as standby or port-channel mode.
Refer to the Cisco Internet Streamer CDS 2.4 Software Configuration Guide for detailed instruction.
2.
Use the client IP address as the load balancing algorithm.
Assuming ether-channel (also known as port-channel) is used between the upstream router/switch
and the SE for streaming real-time data, the ether-channel load balance algorithms on the upstream
switch/router and the SE should be configured as "Src-ip" and "Destination IP" respectively. Using
this configuration ensures session stickiness and general balanced load distribution based on clients’
IP addresses. Also, distribute your client IP address space across multiple subnets so that the load
balancing algorithm is effective in spreading the traffic among multiple ports.
and the SE for streaming real-time data, the ether-channel load balance algorithms on the upstream
switch/router and the SE should be configured as "Src-ip" and "Destination IP" respectively. Using
this configuration ensures session stickiness and general balanced load distribution based on clients’
IP addresses. Also, distribute your client IP address space across multiple subnets so that the load
balancing algorithm is effective in spreading the traffic among multiple ports.
Note
The optimal load-balance setting on the switch for traffic between the Content Acquirer and
the edge Service Engine is dst-port, which is not available on the 3750, but is available on
the Catalyst 6000 series.
the edge Service Engine is dst-port, which is not available on the 3750, but is available on
the Catalyst 6000 series.