Alpine CDA-105 Manual Do Utilizador
7
-EN
Adjusting Volume
Turn the Rotary encoder until the desired sound is
obtained.
obtained.
Lowering Volume Quickly
Activating the Audio Mute function will instantly lower the volume
level by 20 dB.
level by 20 dB.
Press MUTE to activate the MUTE mode.
The audio level will decrease by about 20 dB.
Pressing MUTE again will bring the audio back to its
previous level.
previous level.
Setting the Time
1
Press and hold F/SETUP for at least 2 seconds to
activate the SETUP selection mode.
activate the SETUP selection mode.
2
Turn the Rotary encoder to select CLOCK ADJUST,
and then press
and then press
/ENT.
3
Turn the Rotary encoder to set hour.
4
Press
/ENT.
5
Repeat steps 3 and 4 above to set minute.
6
Press and hold F/SETUP for at least 2 seconds to
return to normal mode.
return to normal mode.
• Pressing
/ESC returns to the previous SETUP mode.
• If no operation is performed for 60 seconds, SETUP is canceled.
• To synchronize the clock to another clock/watch or radio time
• To synchronize the clock to another clock/watch or radio time
announcement, press and hold
/ENT for at least 2 seconds after
setting the “hour.” Minutes will reset to 00. If the display shows over
“30” minutes when you do this, the time will advance one hour.
“30” minutes when you do this, the time will advance one hour.
This unit cannot receive HD Radio signals (digital terrestrial radio). In
order to activate the digital radio functions described below, an optional
HD Radio Tuner module must be connected through the Ai-NET bus.
order to activate the digital radio functions described below, an optional
HD Radio Tuner module must be connected through the Ai-NET bus.
If the unit is connected to a Tagging compatible device, you can use the
iTunes Tagging function. For details, refer to the Owner’s Manual of the
Tagging compatible device.
iTunes Tagging function. For details, refer to the Owner’s Manual of the
Tagging compatible device.
Listening to Radio
1
Press SOURCE/
to select TUNER mode.
2
Press BAND repeatedly until the desired radio band
is displayed.
is displayed.
F1 (FM1)
F2 (FM2)
AM
F1 (FM1)
3
Press TUNE/A.ME to select the tuning mode.
DX SEEK (Distance mode)
SEEK (Local mode)
OFF (Manual mode)
DX SEEK (Distance mode)
• The initial mode is Distance mode.
Distance mode:
Both strong and weak stations will be automatically tuned in
(Automatic Seek Tuning).
(Automatic Seek Tuning).
Local mode:
Only strong stations will be automatically tuned in (Automatic
Seek Tuning).
Seek Tuning).
Manual mode:
The frequency is manually tuned in steps (Manual tuning).
4
Press
or
to tune in the desired station.
Holding down
or
will change the frequency
continuously.
• If DIGITAL SEEK is set to ON, the SEEK UP/DOWN functions only
stop on digital station frequencies while receiving an HD Radio
broadcast. Refer to “Digital Seek ON/OFF Setting” (page 18).
broadcast. Refer to “Digital Seek ON/OFF Setting” (page 18).
Controllable with Remote Control
This unit can be controlled with an optional Alpine remote
control. For details, consult your Alpine dealer.
Point the optional remote control transmitter at the remote
control sensor.
control. For details, consult your Alpine dealer.
Point the optional remote control transmitter at the remote
control sensor.
Connectable to Remote Control Interface Box
This unit may be controlled from the vehicle’s audio controls.
An optional Alpine Remote Control Interface Box must be
used. For details, contact your Alpine dealer.
An optional Alpine Remote Control Interface Box must be
used. For details, contact your Alpine dealer.
Remote control sensor
Radio
BAND
/
/
TUNE/A.ME
Rotary encoder
/ENT
Preset buttons
(1 through 6)
(1 through 6)
/ESC
SOURCE/