Alpine cda-9830r Manual Do Utilizador
16
-EN
Sound Setting
Adjusting Balance (Between Left and Right)/
Fader (Between Front and Rear)/Defeat
Fader (Between Front and Rear)/Defeat
1
Press Rotary encoder repeatedly to choose the
desired mode.
desired mode.
Each press changes the modes as follows:
SUBWOOFER*
1
→ BALANCE → FADER → DEFEAT →
VOLUME
→ SUBWOOFER*
1
Subwoofer : 0 ~ +15
Balance : L15 ~ R15
Fader : R15 ~ F15
Defeat : ON/OFF
Volume : 0 ~ 35
Balance : L15 ~ R15
Fader : R15 ~ F15
Defeat : ON/OFF
Volume : 0 ~ 35
Press g or f after selecting the Subwoofer mode,
and the subwoofer output phase is toggled NORMAL
(PHASE 0°) or REVERS (PHASE 180°).
and the subwoofer output phase is toggled NORMAL
(PHASE 0°) or REVERS (PHASE 180°).
• If the Rotary encoder is not pressed within 5 seconds after
selecting the BALANCE, FADER, DEFEAT or SUBWOOFER
mode, the unit automatically returns to normal mode.
mode, the unit automatically returns to normal mode.
*
1
When the subwoofer mode is set to OFF, its level and phase cannot
be adjusted.
be adjusted.
2
Turn the Rotary encoder until the desired sound
is obtained in each mode.
is obtained in each mode.
By setting Defeat ON, previously adjusted setting of EQ
will return to the factory defaults and MX is turned off.
will return to the factory defaults and MX is turned off.
• Depending on the connected devices, some functions and display
indications do not work.
SOURCE/
POWER
POWER
g
f
Preset buttons
(1 or 2)
(1 or 2)
BAND/
TEL.
TEL.
Rotary encoder
MX
Adjusting and Storing the built-in Crossover
The High and Low Pass Filters on this unit can be adjusted to suit
your personal taste.
your personal taste.
1
Press and hold MENU for at least 2 seconds.
2
Press MENU to select HPF/LPF.
3
Press BAND/TEL. to change the setting mode.
HPF
↔ LPF*
* When the subwoofer output of this unit is turned off, LPF and
phase are deactivated.
4
Turn the Rotary encoder to select the desired
setting.
setting.
HPF (Setting the High Pass Filter):
FLAT (OFF)
↔ 80Hz ↔ 120Hz ↔160Hz
All frequencies above the selected cutoff are output.
LPF (Setting the Low Pass Filter):
FLAT (OFF)
↔ 80Hz ↔ 120Hz ↔160Hz
All frequencies below the selected cutoff are output.
(Only available when using the subwoofer output from this
unit.)
(Only available when using the subwoofer output from this
unit.)
To store the adjusted contents
1) Press and hold, for at least 2 seconds, the preset
buttons (1 or 2) into which you wish to store the adjusted
contents.
contents.
5
Press the Rotary encoder to confirm the
adjusted contents.
adjusted contents.
The adjusted contents are not stored if the Rotary encoder
is not pressed.
is not pressed.
6
After setting, press and hold MENU for at least 2
seconds to return to normal mode, or press MENU
and select RETURN to return to normal mode.
seconds to return to normal mode, or press MENU
and select RETURN to return to normal mode.
• The setting mode returns to normal mode if no buttons are pressed
within 15 seconds.
• These functions are inoperative when an external, Ai-NET
processor is connected.
• Except when the HPF and LPF are turned to OFF, the subwoofer
is in monaural mode.
• When the subwoofer is set to OFF, LPF mode and change of phase
does not work.
MENU