Manualsbrain.com
  1. Manuais
  2. Marcas
  3. Alpine
  4. CDE-9845RB
  5. Manual Do Utilizador

Alpine CDE-9845RB Manual Do Utilizador

Download
Página de 29
14
-EN
Sound Setting
CDE-9845RX
CDE-9843RX/CDE-9841R
Adjusting Bass/Treble/Balance (Between Left
and Right)/Fader (Between Front and Rear)/
Defeat
1
Press Rotary encoder (MODE/LOUD) (CDE-
9845RX) or MODE/LOUD (CDE-9843RX/CDE-
9841R) repeatedly to choose the desired mode.
Each press changes the modes as follows:
BASS 
→ TREBLE → SUBW*
1
 
→ BALANCE → FADER →
DEFEAT 
→ VOLUME → BASS
Bass Level: -7 ~ +10
Treble Level:  -7 ~ +7
Subwoofer : 0 ~ +15
Balance : L15 ~ R15
Fader : R15 ~ F15
Defeat : ON/OFF
Volume : 0 ~ 35
• If the Rotary encoder (MODE/LOUD) or MODE/LOUD is not
pressed within 5 seconds after selecting the BALANCE, FADER,
DEFEAT or SUBWOOFER mode, the unit automatically returns to
normal mode.
CDE-9845RX:
• If the Rotary encoder (MODE/LOUD) is not pressed within 5
seconds after selecting the BASS or TREBLE mode, the unit
automatically returns to normal mode.
CDE-9843RX/CDE-9841R:
• If the MODE/LOUD is not pressed within 15 seconds after
selecting the BASS or TREBLE mode, the unit automatically
returns to normal mode.
*
1
When the subwoofer mode is set to OFF, its level cannot be
adjusted.
2
Turn the Rotary encoder (CDE-9845RX) or press
4
4
4
4
4 and 3
3
3
3
3 (CDE-9843RX/CDE-9841R) until the
desired sound is obtained in each mode.
By setting Defeat ON, previously adjusted settings of
BASS and TREBLE will return to the factory defaults.
Setting the Bass Control
You can change the bass frequency emphasis to create your own tonal
preference.
1
CDE-9845RX:
Press CENTER f. to select the Bass Control mode.
BASS 
→ TREBLE → normal mode → BASS
CDE-9843RX/CDE-9841R:
Press MODE/LOUD to select the Bass Control
mode.
BASS 
→ TREBLE → SUBW → BALANCE → FADER →
DEFEAT 
→ VOLUME → BASS
2-1
Setting the bass centre frequency:
Press g or f to select the desired bass centre
frequency.
60Hz 
↔ 80Hz ↔ 100Hz ↔ 120Hz ↔ 60Hz
The displayed bass frequency is emphasized.
2-2
Setting the bass band width (Q-Factor):
Press BAND to select the desired bass band
width.
Changes the boosted bass band width to wide or narrow.
A wide setting will boost a wide range of frequencies
above and below the centre frequency. A narrower setting
will boost only frequencies near the centre frequency.
2-3
*2
Setting the bass level:
Turn the Rotary encoder (CDE-9845RX) or press
4
4
4
4
4 and 3
3
3
3
3 (CDE-9843RX/CDE-9841R) to select the
desired bass level (-7~+10).
You can emphasize or weaken the bass frequency.
• If no operation is performed within 15 seconds, the bass control
setting will be turned off automatically.
• The bass level settings will be individually memorized for each
source (FM, MW (LW), CD, etc.) until the setting is changed. The
bass frequency and bass band width settings adjusted for one
source are effective for all other sources (FM, MW (LW), CD etc.).
• This function is inoperable when DEFEAT is set to ON.
*
2
CDE-9845RX:
The adjustment can also be made by pressing the Rotary encoder
(MODE/LOUD). Refer to “Adjusting Bass/Treble/Balance
(Between Left and Right)/Fader (Between Front and Rear)/Defeat”
(this page).
BAND
Rotary encoder
(MODE/LOUD)
g
 f
CENTER f.
4
3
MODE/LOUD
g
 f
BAND
......................................
   →     1       →        2       →        3       →        4
(Narrow)
←
→(Wide)