Alpine dva-9965r Manual Do Utilizador
48
-EN
ALPINE DVA-9965R 68-02065Z31-A (EN)
7
Adjust the level by turning the Rotary encoder.
8
To adjust other bands, repeat steps 6 and 7.
9
When the setting is complete, press and hold
MENU for at least 2 seconds.
MENU for at least 2 seconds.
• When the speaker is set to the “OFF” mode, the level of the
graphic equalizer for that speaker cannot be adjusted. Refer to
“Setting the Speakers” (page 46).
“Setting the Speakers” (page 46).
• Check the playable frequency ranges of the connected speakers
before making the equalizer adjustments. If the speaker’s playable
frequency range is 55 Hz to 30 kHz, for example, adjusting the
40 Hz or 20 Hz band has no effect. Additionally, you may overload
and damage the speakers.
frequency range is 55 Hz to 30 kHz, for example, adjusting the
40 Hz or 20 Hz band has no effect. Additionally, you may overload
and damage the speakers.
• When graphic EQ is adjusted, the adjustment for parametric EQ
becomes ineffective.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 52.
Parametric Equalizer Adjustments
The frequency bands of the graphic equalizer are fixed. This makes it
very difficult to correct for undesired peaks and dips at specific
frequencies. The parametric equalizer’s centre frequency can be tuned
to these specific frequencies. Then, the bandwidth (Q) and level are
fine-tuned, independently, to make the necessary corrections. The
parametric equalizer function is an advanced tool for serious
audiophiles.
very difficult to correct for undesired peaks and dips at specific
frequencies. The parametric equalizer’s centre frequency can be tuned
to these specific frequencies. Then, the bandwidth (Q) and level are
fine-tuned, independently, to make the necessary corrections. The
parametric equalizer function is an advanced tool for serious
audiophiles.
1
Check that Defeat mode is off (page 22) and P.EQ is
selected in “Setting User’s EQ mode” (page 23).
selected in “Setting User’s EQ mode” (page 23).
2
Press and hold MENU for at least 2 seconds.
3
Select the Parametric EQ mode by sliding your
finger on the GlideTouch bar to the left or right.
Press the GlideTouch bar under the Parametric
EQ mode.
finger on the GlideTouch bar to the left or right.
Press the GlideTouch bar under the Parametric
EQ mode.
4
Select L+R or L/R by pressing and holding BAND
for at least 2 seconds.
for at least 2 seconds.
L+R: Sets the same adjustment values for the left and
right channels.
L/R: Different adjustment values can be set for the left
and right channels.
When graphic EQ is adjusted, this setting will be turned
off.
off.
5
Select the desired channel by sliding your finger
on the GlideTouch bar to the left or right. The
channel changes by pressing the GlideTouch
bar.
on the GlideTouch bar to the left or right. The
channel changes by pressing the GlideTouch
bar.
6
Press BAND to select the band.
7
Select the frequency sliding your finger on the
GlideTouch bar to the left or right. Press the
GlideTouch bar under the frequency.
GlideTouch bar to the left or right. Press the
GlideTouch bar under the frequency.
8
Press SOURCE/POWER to set the band width (Q).
8
Select the desired channel by pressing BAND.
• The speakers display differs, depending on the connected speakers.
9
Adjust the calculated time correction value (0.00 to
20.00ms) by turning the Rotary encoder.
20.00ms) by turning the Rotary encoder.
• The time correction values can be adjusted with the GlideTouch
bar.
Switching the Phase
10
Switch the phase (PHASE) by pressing the
SOURCE/POWER.
SOURCE/POWER.
11
To adjust other channels, repeat steps 8 to 10.
12
When the setting is complete, press and hold
MENU for at least 2 seconds.
MENU for at least 2 seconds.
• When changing the time correction value, refer to “Setting the
Time Correction Unit” (page 29).
• When the speaker is set to the “OFF” mode, the TCR for that
speaker cannot be set. Refer to “Setting the Speakers” (page 46).
• The adjustment (AUTO TCR) cannot be automatically set on this
unit.
• When the setting is complete, it is recommended to store the setting
contents. For storing, refer to page 52.
Graphic Equalizer Adjustments
The graphic equalizer allows you to modify the sound using 31 bands
each for the front (left and right), rear (left and right) and centre
speakers. An additional 10 bands are available for the subwoofer. This
allows you to customize the sound to suit your taste.
each for the front (left and right), rear (left and right) and centre
speakers. An additional 10 bands are available for the subwoofer. This
allows you to customize the sound to suit your taste.
1
Check that Defeat mode is off (page 22) and G.EQ
is selected in “Setting User’s EQ mode” (page 23).
is selected in “Setting User’s EQ mode” (page 23).
2
Press and hold MENU for at least 2 seconds.
3
Select the Graphic EQ mode by sliding your finger
on the GlideTouch bar to the left or right.
Press the GlideTouch bar under the Graphic EQ
mode.
on the GlideTouch bar to the left or right.
Press the GlideTouch bar under the Graphic EQ
mode.
4
Select L+R or L/R by pressing and holding BAND
for at least 2 seconds.
for at least 2 seconds.
L+R: Sets the same adjustment values for the left and
right channels.
L/R: Different adjustment values can be set for the left
and right channels.
When parametric EQ is adjusted, this setting will be
turned off.
turned off.
5
Select the channel by sliding your finger on the
GlideTouch bar to the left or right. Press the
GlideTouch bar under the channel.
GlideTouch bar to the left or right. Press the
GlideTouch bar under the channel.
6
Select the desired band by pressing BAND.