ASUS TX97-XE Manual Do Utilizador
18
ASUS TX97-XE User’s Manual
III. INSTALLATION
Jumpers
III. INST
ALLA
TION
Compatible Cyrix CPU Identification
The only Cyrix CPU that is supported on this motherboard is
labeled Cyrix 6x86 PR166+ but must be Revision 2.7 or later.
Look on the underside of the CPU for the serial number. The
number should read G8DC6620A or later.
labeled Cyrix 6x86 PR166+ but must be Revision 2.7 or later.
Look on the underside of the CPU for the serial number. The
number should read G8DC6620A or later.
6. Voltage Regulator Output Selection (VID0, 1, 2, 3)
These jumpers set the voltage supplied to the CPU. VID1 for 3.4V(STD) is
ignored, therefore, the jumper setting for 2.8V(Dual) may work for both
3.4V(STD) and 2.8V(Dual).
ignored, therefore, the jumper setting for 2.8V(Dual) may work for both
3.4V(STD) and 2.8V(Dual).
Intel Pentium (P54C)
(75MHz-200MHz)
(75MHz-200MHz)
Pentium MMX (P55C)
(150MHz-233MHz)
(150MHz-233MHz)
AMD-K6
(PR166 and faster)
(PR166 and faster)
AMD-K5
(PR75-PR133)
(PR75-PR133)
IBM/Cyrix 6x86(MX)
(PR166 and faster)
(PR166 and faster)
IBM/Cyrix 6x86(M1)
(PR166 and faster)
(PR166 and faster)
WARNING!
Because CPU designs change rapidly, the following chart is only
intended as a simple quideline and is not intended to be true for your CPU. Look
for the CPU voltage included with your CPU and follow the Voltage setting
diagramed below the chart.
for the CPU voltage included with your CPU and follow the Voltage setting
diagramed below the chart.
Manufacturer
CPU Type
Single Plane Dual Plane
VID3
VID2
VID1 VID0
Intel/AMD/IBM/Cyrix P54C/CS/K5/M1 3.5V(VRE)
----
[----]
[2-3]
[----]
[1-2]
AMD/IBM/Cyrix
K6-166,200/MX ----
2.9V(Dual)
[----]
[2-3]
[2-3]
[1-2]
Intel/AMD
P54C/CS/K5
3.4V(STD)
----
[----]
[2-3]
[2-3]
[2-3]
Intel
P55C
----
2.8V(Dual)
[----]
[2-3]
[2-3]
[2-3]
AMD
K6-PR233
----
3.2V(Dual)
[----]
[1-2]
[2-3]
[2-3]
AMD (.25micron)
K6-233,266,300 ----
2.1V(Dual)
[----]
[----]
[2-3]
[1-2]
1.8 Volts
VID1
VID0
VID2
1
2
3
2
3
VID3
VID1
VID0
VID2
1
2
3
2
3
VID3
VID1
VID0
VID2
1
2
3
2
3
VID3
1
2
3
2
3
1
2
3
2
3
1
2
3
2
3
1.9 Volts
2.1 Volts
2.9 Volts
2.8 Volts
2.7 Volts
1
2
3
2
3
1
2
3
2
3
1
2
3
2
3
3.5 V
3.4 V
3.2 Volts
*
*
*
Setting these two jumpers’ VID1 to [2-3] or [----] (removed)
will result in the same voltages respectively.
R
Voltage Regulator Output Selection
VID1
VID0
VID2
1
2
3
2
3
VID3
2.5 Volts