Canon DR40-S-VB Manual Do Utilizador

The procedures for mounting the camera to the ceiling using the indoor dome housing are 
described below.
Before installing the camera, set the IP address and other network information on the camera 
using the "VB Initial Setting Tool".
For details on how to operate the "VB Initial Setting Tool", see VB-M40 Operation Guide.
If using an SD memory card, insert the SD memory card into the camera before installing (see 
"Using an SD Memory Card" in VB-M40 Installation Guide).

 Important

Once the camera is installed to the ceiling, to insert and remove the SD memory card, the camera must 
be removed from the ceiling and the ceiling bracket dismounted.

Using the bundled template, line up the directon of the camera, determine the locations of the 
backside ceiling bracket mounting holes (three) and the ceiling bracket holes, then drill the 
holes into the ceiling.

 Important

When mounting the indoor dome housing, be sure no shavings enter the dome.

Affix with four bundled fixing screw (M3).

Affix with three bundled fixing screw (M3).

From the inside of the ceiling, insert the protrusions on the backside ceiling brackets through 
the mounting holes drilled in step 1.

Temporarily tighten the three bundled ceiling bracket screws (M4) through the ceiling.

Securely attach the safety wire to an anchor or structure. After securing the end of the safety 
wire to the ceiling, secure the other end to the camera using the screw that is fastened to the 
camera.

If an AC adapter PA-V17 (optional) or external power supply is used, connect the power 
connector to the camera. Connect cables to external device I/O terminals and  audio input/
output terminals as necessary (see "Connecting the Camera" in VB-M40 Installation Guide).

Position the ceiling bracket over the screws temporarily tightened in step 5, turn clockwise to 
temporarily secure in place, and completely fasten the screws.

Align the (O) mark on the dome with the (I) mark on the ceiling bracket, and turn clockwise 
until the (I) mark on the dome aligns with the (I) mark on the ceiling bracket. This procedure 
also aligns the ceiling bracket screw hole with the dome fixing screw hole. 

To prevent the dome from rotating, attach one dome fixing screw (M2).

The camera position is initiated (see "Maintenance" in Chapter 4, "Setting Page" of the VB-M40 
Operation Guide).

 Note

While the LED is on, light may reflect inside the dome and be captured on video. If this happens, set the 
LED setting to [Off] (see “LED Setting” in VB-M40 Operation Guide).

Model DR40-C-VB/DR40-S-VB
Type Clear 

type/smoked 

type

Network camera-mounting environments 

Temperature -10 to 50°C (14 to 122°F), humidity 5 to 85%RH 
(non-condensing)

Dimensions (

Φ x H) 204 (112: Dome) x 92 mm  (8.03 (4.41: Dome) x 3.62 in)

*Including ceiling-embedded section: 176 mm (

6.93 in) (H)

Weight 

Approx. 765 g (1.687 lb) (excluding camera)

Smoked (DR40-S-VB)
This dome is approximately 50% transparent. 
Minimum subject illumination
      Day Mode (color) :  

0.8 lux (F1.6, Shutter Speed 1/30 sec., when Smart Shade Control is off)
0.2 lux (F1.6, Shutter Speed 1/8 sec., when Smart Shade Control is off)
0.06 lux (F1.6, Shutter Speed 1/8 sec., when Smart Shade Control is on)

       Night Mode (monochrome) :  

0.02 lux (F1.6, Shutter Speed 1/30 sec., when Smart Shade Control is off)
0.004 lux (F1.6, Shutter Speed 1/8 sec., when Smart Shade Control is off)
0.002 lux (F1.6, Shutter Speed 1/8 sec., when Smart Shade Control is on)

DR40-C-VB/DR40-S-VB  

 

 

   Backside ceiling bracket

204.0 mm (8.03 in)

164.0 mm (6.46 in)

112.0 mm (4.41 in)

84.0 mm

(3.31 in)

92.0 mm

(3.62 in)

Safety Wire

Secure to an 
anchor or 
structure

LAN cable

Ceiling 
bracket

Backside 
ceiling 
bracket

Ceiling board

Dome

Camera

10.0 mm
(0.39 in)

7.0 mm (0.28 in)

Height

Bundled 
screw
M3 x 3

Bundled 
screw
M3 x 4

Bundled 
screw
M4 x 3