Panasonic cx-dvp292n Manual Do Utilizador
E
N
N
G
L
I
S
H
H
32
E
N
N
G
L
I
S
H
H
31
Electrical Connections
CX-DVP292N
CX-DVP292N
34
35
No.
6
4
Item
BATTERY 5A
PARKING BRAKE
VIDEO-CONT
ACC
Resistor (1 k≠)
CX-DVP292N (Rear)
VIDEO OUT
AUDIO OUT
DIGITAL OUT
Not used.
REMOTE IN
(Yellow)
RCA cord (option)
RCA cord (option)
Not used.
ACC power lead
To ACC power, +12 V DC.
To ACC power, +12 V DC.
Battery lead
To the battery, continuous +12 V DC.
To the battery, continuous +12 V DC.
Ground lead
To a clean, bare metallic part of car chassis.
To a clean, bare metallic part of car chassis.
(Black)
(Red)
(Green/yellow stripe)
(Blue/yellow stripe)
Fuse (5 A)
Side brake (parking brake) connection lead
(
(
➡
page 38)
When connected to the lead colored in dark blue of the
Panasonic CD receiver or having an AUX-IN input terminal,
instead of connecting to the ACC power source, the power of
unit can be linked to that of receiver.
Panasonic CD receiver or having an AUX-IN input terminal,
instead of connecting to the ACC power source, the power of
unit can be linked to that of receiver.
Connect the battery power cord to a connector that is
always supplied with power from the car battery.
always supplied with power from the car battery.
4 Power connector
R (Red)
L (White)
(Black)
By performing this connection, remote control
signals can be received by the monitor unit.
(Do not connect the remote control signal receiver
when this connection has been performed.)
signals can be received by the monitor unit.
(Do not connect the remote control signal receiver
when this connection has been performed.)
CY-VM1500EX
Monitor unit
Monitor unit
CY-VM1500EX
Controller unit
(option)
(Rear)
Controller unit
(option)
(Rear)
Video
(Yellow)
(Yellow)
(Black)
Power
connector
connector
Connection cable
(Supplied to CY-VM1500EX)
(Supplied to CY-VM1500EX)
R (Red)
L (White)
Video
(Yellow)
(Yellow)
POW
ER
Remote control
signal receiver
signal receiver
Double-sided tape
Attaching the remote
control signal receiver
control signal receiver
When connecting or disconnecting the cord, be
absolutely sure to take hold of the molded part of
the plug (and not the cord itself) and proceed.
absolutely sure to take hold of the molded part of
the plug (and not the cord itself) and proceed.
6 Cord clamp
Caution:
≥
This product is designed to operate with a 12 V DC, negative ground battery system.
≥
To prevent damage to the unit, be sure to follow the connection diagram below.
≥
Remove approximately 5 mm of protective covering from the ends of the leads before connecting.
≥
Do not insert the power connector into the unit until the wiring is completed.
≥
Be sure to insulate any exposed wires from a possible short-circuit from the car chassis. Bundle all
cables and keep cable terminals free from touching any metal parts.
cables and keep cable terminals free from touching any metal parts.
≥
Remember, if your car has a drive computer or a navigation computer, the data of its memory may be
erased when the battery terminals are disconnected.
erased when the battery terminals are disconnected.
1
1
Q’ty
Power connector
Cord clamp
❐ Basic System Configuration
❐ Accessories for Use
Examples of system combination:
≥
Color LCD monitor (CY-VM1500EX, option)
Note:
≥
Refer to the operating instructions for the connected devices, in addition.
≥
Select the monitor system (PAL/NTSC) to suit the type of DVD’s disc you have inserted when connecting the
LCD monitor CY-VM1500EX.
LCD monitor CY-VM1500EX.
≥
The LCD monitor CY-VMR5800N is an RGB connection unit which has been designed especially only for
Panasonic mobile navigation system. This DVD player cannot be connected to the LCD monitor
CY-VMR5800N.
Panasonic mobile navigation system. This DVD player cannot be connected to the LCD monitor
CY-VMR5800N.