Panasonic dvd-f65e Manual Do Utilizador

RQT67

3

0

Signal system:PAL 625/50, PAL525/60, NTSC
Operating temperature range:

i

5 to 

i

35 

o

C

5 to 90 % RH (no condensation)

(1) DVD-RAM (DVD-VR compatible)
(2) DVD-Audio
(3) DVD-Video
(4) DVD-R (DVD-Video compatible)
(5) CD-Audio (CD-DA)
(6) Video CD
(7) SVCD (Conforming to IEC62107)
(8) CD-R/CD-RW

(CD-DA, Video-CD formatted discs)

(9) MP3/WMA

≥

Maximum number of tracks and groups 

recognizable: 999 tracks and 99 
groups

≥

Compatible compression rate:

MP3: between 32 kbps and 320 kbps
WMA: between 48 kbps and 192 kbps

(10) JPEG

≥

Exif Ver 2.1 JPEG Baseline files

≥

Maximum number of pictures and 

groups recognizable:
3000 pictures and 300 groups

≥

Picture resolution:

between 320

t

240 and 6144

t

4096 pixels (Sub sampling is 4:2:2 or 
4:2:0)

(11) HighMAT Level 2 (Audio and Image)

 Output level:

1 Vp-p (75 

≠

)

 Output terminal:

Pin jack (1 system)/AV

 Y output level:

1 Vp-p (75 

≠

)

 C output level:

NTSC; 0.286 Vp-p (75 

≠

)

PAL; 0.300 Vp-p (75 

≠

)

 Output terminal:  S terminal (1 system)/AV

Y output level:

1 Vp-p (75 

≠

)

P

B

 output level:

0.7 Vp-p (75 

≠

)

P

R

 output level:

0.7 Vp-p (75 

≠

)

Output terminal:

Pin jack 

(1 system, Y: green, P

B

: blue, P

R

: red)

R output level:

0.7 Vp-p (75 

≠

)

G

 

output level:

0.7 Vp-p (75 

≠

)

B output level:

0.7 Vp-p (75 

≠

)

Output terminal:

AV

 Output level:

2 Vrms (1 kHz, 0 dB)

 Output terminal:

Pin jack/AV

 Number of terminals:  2 channel:1 system

(1) Frequency response:

≥

DVD (linear audio):

4 Hz–22 kHz (48 kHz sampling)
4 Hz–44 kHz (96 kHz sampling)

≥

DVD-Audio:

4 Hz–88 kHz (192 kHz sampling)

≥

CD audio:

4 Hz–20 kHz

(2) S/N ratio:

≥

CD audio:

115 dB

(3) Dynamic range:

≥

DVD (linear audio):

102 dB

≥

CD audio:

98 dB

(4) Total harmonic distortion:

≥

CD audio:

0.0025 %

Optical digital output:

Optical terminal

Wave length:

658 nm/790 nm

Laser power:

CLASS 2/CLASS 1

Bølgelengde:

658 nm/790 nm

Laser-styrke:Ingen farlig strålning sendes ut

AC 220–240 V, 50 Hz

15 W

Dimensions: 430 (W)

k

405 (D)

k

59.7 (H) mm

4.1 k

g

approx. 2.8 W

[Note]

Specifications are subject to change without 
notice. Mass and dimensions are approximate.

≥

Check the connections. 

≥

Check the volume on the equipment you have connected.

≥

Ensure that the input settings on the other equipment are correct.

≥

Turn Advanced surround off if it causes distortion. 

≥

Output from this unit will be in stereo (two channels) when Advanced surround is on. Turn Advanced 

surround off if you are using three or more speakers.

≥

If the “D.MIX” indicator on the display goes out while playing a multi-channel DVD-Audio disc, sound 

only comes from the front left and right speakers. Read the disc's instructions for details. 

≥

Press [

1

] (PLAY) to restore normal play after changing the speed.

≥

Noise may occur when playing WMA files.

≥

If you have connected this unit to other equipment through the DIGITAL AUDIO OUT terminal, ensure 

you have selected the correct settings for “Dolby Digital”, “DTS Digital Surround” and “MPEG” in the 
SETUP menus’ Audio menu.

≥

Dialogue enhancer and Advanced surround do not work when the unit is outputting bitstream signals.

≥

Advanced surround does not work if you have changed the play speed.

≥

You inserted a disc the unit cannot play; insert one it can.

≥

You inserted a blank DVD-RAM.

≥

Disc is dirty: Wipe it clean.

∑∑

∑∑

≥

Trouble may have occurred. The number following “H” depends on the status of the unit.

Reset procedure:
Press [

Í

/I] to switch the unit to the standby mode and then back to ON. Alternatively, press [

Í

/I] to 

switch the unit to the standby mode, disconnect the AC mains lead, and then reconnect it.

≥

If the service numbers fail to clear, note the service number and contact a qualified service person.

≥

You are trying to display incompatible pictures.

≥

Go to Video in the SETUP menus, and select “Enable (NTSC Disc Only)” in “Progressive Out 

(Component)”.

≥

Go to Display in the SETUP menus, and select “On” for “On-Screen Messages”. 

≥

Press [DISPLAY], and press [

2

, 

1

] to highlight the Bar Position icon, then press [

3

, 

4

] to adjust the 

position.

≥

Go to Disc in the SETUP menus, and select the preferred language for “Menus”.