Panasonic sb-fw140 Manual Do Utilizador
ENGLISH
ESP
AÑOL
FRANÇAIS
SVENSKA
RQT5590
4
Speaker set-up
a
Front speaker (Left)
b
Center speaker (not included)
c
TV (not included)
d
Receiver or amplifier (not included)
e
Front speaker (Right)
f
Surround speaker (Right) (not included)
g
Surround speaker (Left) (not included)
h
Speaker cables
A
Location
In order to obtain the best acoustic effects possible, we suggest that
you follow the guidelines below as closely as possible.
you follow the guidelines below as closely as possible.
Place the speaker on a flat, level and secure base.
Face the rear of the speaker toward a wide, solid wall
surface.
surface.
There is a bass reflex on the rear of the speaker, so place the speaker
so that there is a space of approximately 5 cm between it and the
wall.
so that there is a space of approximately 5 cm between it and the
wall.
Hang a thick curtain or similar material on the wall toward
which the speaker is facing.
which the speaker is facing.
If the surface facing the speaker is a solid wall or window, hanging a
curtain will prevent sound reflection or resonance from occurring.
curtain will prevent sound reflection or resonance from occurring.
Don’t place the speaker too close to a record player.
The speaker may cause the record player to vibrate or howling (a
high-pitched whining sound) may occur. This can be prevented by
keeping sufficient distance between the speaker and the record player,
or by placing some felt underneath the record player.
high-pitched whining sound) may occur. This can be prevented by
keeping sufficient distance between the speaker and the record player,
or by placing some felt underneath the record player.
B
Connections
•
Before making the connections, switch OFF the power to the re-
ceiver or amplifier.
ceiver or amplifier.
•
Use with a receiver or amplifier having 6
Ω
impedance for these
speakers.
•
Be sure to connect only positive (+) wires to positive (+) terminals,
and negative (–) wires to negative (–) terminals.
and negative (–) wires to negative (–) terminals.
Connecting the speaker cable to the speaker
CAUTION
To prevent damage to circuitry, never short-circuit positive (+) and
negative (–) speaker wires.
negative (–) speaker wires.
Instalación de altavoces
a
Altavoz delantero (izquierdo)
b
Altavoz central (opcional)
c
Televisor (opcional)
d
Receptor o amplificador (opcional)
e
Altavoz delantero (derecho)
f
Altavoz de sonido ambiental (derecho) (opcional)
g
Altavoz de sonido ambiental (izquierdo) (opcional)
h
Cables de altavoces
A
Ubicación
Para obtener el mejor efecto acústico posible, le sugerimos que siga
atentamente las instrucciones indicadas a continuación.
atentamente las instrucciones indicadas a continuación.
Colocar el altavoz en un lugar plano, nivelado y seguro.
La parte trasera del altavoz debe quedar hacia una pared
grande y sólida.
grande y sólida.
En la parte trasera del altavoz existe un altavoz de reflejo de graves,
por lo tanto se debe dejar una separación de 5 cm aproximadamente
entre el altavoz y la pared.
por lo tanto se debe dejar una separación de 5 cm aproximadamente
entre el altavoz y la pared.
Colgar una cortina gruesa o un material similar en la pared
hacia la que mira el altavoz.
hacia la que mira el altavoz.
Si la superficie hacia la que mira el altavoz es una pared sólida o una
ventana, colgando una cortina se impedirán las reflexiones del sonido
o la resonancia.
ventana, colgando una cortina se impedirán las reflexiones del sonido
o la resonancia.
No colocar el altavoz muy cerca de un tocadiscos.
El altavoz puede hacer que el tocadiscos vibre o produzca aullidos
(un sonido de alta frecuencia). Se debe evitar esto manteniendo
suficiente distancia entre el altavoz y el tocadiscos, o colocando un
paño de fieltro debajo del tocadiscos.
(un sonido de alta frecuencia). Se debe evitar esto manteniendo
suficiente distancia entre el altavoz y el tocadiscos, o colocando un
paño de fieltro debajo del tocadiscos.
B
Conexiones
•
Antes de realizar las conexiones, desconectar la alimentación del
receptor o del amplificador.
receptor o del amplificador.
•
Utilice un receptor o amplificador con una impedancia de 6
Ω
para
estos altavoces.
•
Asegurarse de conectar sólo los conductores positivos (+) en los
terminales (+) y los conductores negativos (–) en los terminales (–).
terminales (+) y los conductores negativos (–) en los terminales (–).
C
Conexión de un cable de altavoz a un altavoz
PRECAUCIÓN
Para no dañar el circuito, nunca se debe permitir que los conductores
de altavoces positivo (+) y negativo (–) hagan cortocircuito.
de altavoces positivo (+) y negativo (–) hagan cortocircuito.