JVC dr-m7s Manual Do Utilizador
Masterpage:Right-No-Heading
59
Filename [DR-M7EK_08Recording.fm]
Page 59
April 2, 2004 11:21 am
F
Enter the recording stop time.
Press w e to select “STOP”, then press rt repeatedly to
set the desired stop time.
set the desired stop time.
● Each press of rt advances/goes back the stop time in 1-min.
increments.
● To advance/go back the stop time in 30-min. increments, press
and hold rt.
G
Enter the channel position.
Press w e to select “TV PROG”, then press rt
repeatedly to select the desired channel.
repeatedly to select the desired channel.
H
Set the other recording options as required.
Refer to step
E in “VIDEO Plus+
®
Timer Programming”
(
墌
pg. 56).
I
Access the confirmation screen.
Press ENTER.
J
Complete timer programming.
Press ENTER.
● To programme another timer, repeat steps B – J.
K
Engage the unit’s timer mode.
Press # (TIMER). The unit turns off automatically and
“#” appears on the front display panel.
“#” appears on the front display panel.
● To disengage the timer mode, press # (TIMER) again.
NOTES:
● The beginning of a programme may not be recorded. Also, if
the 1st programme’s recording stop time and the 2nd
programme’s recording start time is the same, the ending of the
1st programme may not be recorded.
programme’s recording start time is the same, the ending of the
1st programme may not be recorded.
● If the copy limited programme is received during timer-
recording, the unit enters Record Pause mode. Recording starts
again if it is switched to a recordable broadcast during the
time you programmed.
again if it is switched to a recordable broadcast during the
time you programmed.
Satellite Receiver Users
To timer-record a satellite broadcast using Manual Timer
Programming:
A Perform “Satellite Receiver Control Setting” on page 28.
B Perform “Manual Timer Programming”. In step G, press
Programming:
A Perform “Satellite Receiver Control Setting” on page 28.
B Perform “Manual Timer Programming”. In step G, press
AUX to change “TV PROG” to “SAT”. Then press rt to
enter the channel position for the satellite broadcast. In
step
enter the channel position for the satellite broadcast. In
step
H, you cannot set “VPS/PDC” to “ON”.
C Leave the satellite receiver’s power on.
PDC Recording
Now available from some TV stations, PDC (Programme
Delivery Control) is a service designed to assure safe,
accurate timer recording. With this system, special code
signals are transmitted together with the audio/video signals.
These code signals control your unit and have precedence
over the advertised times which you may have preset into the
timer. This means that your unit will start and stop recording
when the preset TV programmes actually start and end —
even if the broadcast time of a preset TV programme is
changed from what has been advertised. PDC is currently
available nationally on BBC1, BBC2, Ch.4 and Ch.5, except
from a few small relay transmitters. Ch.3 operates a PDC
service in some areas. All channels intend to offer this
service in due course. Check your TV programme listing
guide for latest information. If the channel you intend to
record does not offer a PDC service your unit will not start
recording if PDC has been selected. Be sure to set PDC to
“OFF” if PDC is not available on your selected channel.
(See step
Delivery Control) is a service designed to assure safe,
accurate timer recording. With this system, special code
signals are transmitted together with the audio/video signals.
These code signals control your unit and have precedence
over the advertised times which you may have preset into the
timer. This means that your unit will start and stop recording
when the preset TV programmes actually start and end —
even if the broadcast time of a preset TV programme is
changed from what has been advertised. PDC is currently
available nationally on BBC1, BBC2, Ch.4 and Ch.5, except
from a few small relay transmitters. Ch.3 operates a PDC
service in some areas. All channels intend to offer this
service in due course. Check your TV programme listing
guide for latest information. If the channel you intend to
record does not offer a PDC service your unit will not start
recording if PDC has been selected. Be sure to set PDC to
“OFF” if PDC is not available on your selected channel.
(See step
H on page 59.)
NOTES:
● When you use Manual Timer Programming, set the start
time (PDC time) exactly as advertised in the TV listing. A
different time than advertised will result in no recording.
different time than advertised will result in no recording.
● PDC recording is also possible when a satellite receiver or
a cable system is connected to L-2 IN/DECODER
connector on your unit.
connector on your unit.
● PDC recording is also possible via the L-1 IN/OUT
connector.
DR-M7EK_01.book Page 59 Friday, April 2, 2004 11:21 AM