Yamaha 02R96 Manual Do Utilizador
244
Appendix A: Parameter Lists
02R96—Owner’s Manual
FREEZE
One input, one output basic sampler.
ST REVERB
Two input, two output stereo reverb.
Parameter
Range
Description
REC MODE
MANUAL, INPUT
In MANUAL mode, recording is started by pressing the REC
and PLAY buttons. In INPUT mode, Record-Ready mode is
engaged by pressing the REC button, and actual recording is
triggered by the input signal.
and PLAY buttons. In INPUT mode, Record-Ready mode is
engaged by pressing the REC button, and actual recording is
triggered by the input signal.
REC DLY
–1000 to +1000 ms
Recording delay. For plus values, recording starts after the
trigger is received. For minus values, recording starts before
the trigger is received.
trigger is received. For minus values, recording starts before
the trigger is received.
TRG LVL
–60 to 0 dB
Input trigger level (i.e., the signal level required to trigger
recording or playback)
recording or playback)
TRG MASK
0–1000 ms
Once playback has been triggered, subsequent triggers are
ignored for the duration of the TRG MASK time.
ignored for the duration of the TRG MASK time.
PLAY
MODE
MODE
MOMENT, CONT.,
INPUT
INPUT
In MOMENT mode, the sample plays only while the that the
PLAY button is pressed. In CONT mode, playback continues
once the PLAY button has been pressed. The number of
times the sample plays is set using the LOOP NUM parame-
ter. In INPUT mode, playback is triggered by the input signal.
PLAY button is pressed. In CONT mode, playback continues
once the PLAY button has been pressed. The number of
times the sample plays is set using the LOOP NUM parame-
ter. In INPUT mode, playback is triggered by the input signal.
START
1
1. 0.0–5941.0 ms (fs=44.1 kHz), 0.0 ms–5458.3 ms (fs=48 kHz), 0.0–2970.5 ms (fs=88.2 kHz),
0.0 ms–2729.1 ms (fs=96 kHz)
Playback start point in milliseconds
END
1
Playback end point in milliseconds
LOOP
1
Loop start point in milliseconds
LOOP NUM
0–100
Number of times the sample plays
START
[SAMPLE]
[SAMPLE]
0–262000
Playback start point in samples
END
[SAMPLE]
[SAMPLE]
0–262000
Playback end point in samples
LOOP
[SAMPLE]
[SAMPLE]
0–262000
Loop start point in samples
PITCH
–12 to +12 semitones
Playback pitch shift
FINE
–50 to +50 cents
Playback pitch shift fine
MIDI TRG
OFF, C1–C6, ALL
PLAY button can be triggered by using MIDI Note on/off
messages.
messages.
Parameter
Range
Description
REV TIME
0.3–99.0 s
Reverb time
REV TYPE
Hall, Room, Stage, Plate
Reverb type
INI. DLY
0.0–100.0 ms
Initial delay before reverb begins
HI. RATIO
0.1–1.0
High-frequency reverb time ratio
LO. RATIO
0.1–2.4
Low-frequency reverb time ratio
DIFF.
0.0–1.0
Reverb diffusion (left–right reverb spread)
DENSITY
0–100%
Reverb density
HPF
THRU, 21.2 Hz–8.00
kHz
kHz
High-pass filter cutoff frequency
LPF
50.0 Hz–16.0 kHz,
THRU
THRU
Low-pass filter cutoff frequency
E/R BAL.
0–100%
Balance of early reflections and reverb
(0% = all reverb, 100% = all early reflections)
(0% = all reverb, 100% = all early reflections)