Yamaha aw16g Manual Do Utilizador
91
Mixdo
wn and bounce oper
ations
9
D
Effect insert
This lets you insert an internal effect into the chan-
nel. When you move the cursor here and press the
[ENTER] key, a popup window will appear, allow-
ing you to select internal effect 1 or 2.
nel. When you move the cursor here and press the
[ENTER] key, a popup window will appear, allow-
ing you to select internal effect 1 or 2.
E
EQ
Move the cursor here and press the [ENTER] key to
switch EQ on/off.
switch EQ on/off.
F
DYN
Move the cursor here and press the [ENTER] key to
switch dynamics on/off.
switch dynamics on/off.
G
ON/OFF
Move the cursor here and press the [ENTER] key to
switch the channel on/off.
switch the channel on/off.
H
EFF1 (except for the stereo output channel)
I
EFF2 (except for the stereo output channel)
J
AUX1 (except for the stereo output chan-
nel)
nel)
K
AUX2 (except for the stereo output chan-
nel)
nel)
Move the cursor to these knobs and turn the [DATA/
JOG] dial to adjust the send levels to effect buses 1/
2 and AUX buses 1/2.
By moving the cursor to the left of the knob and
pressing the [ENTER] key, you can switch between
pre-fader (send the pre-fader signal to the bus) and
post-fader (send the post-fader signal to the bus).
JOG] dial to adjust the send levels to effect buses 1/
2 and AUX buses 1/2.
By moving the cursor to the left of the knob and
pressing the [ENTER] key, you can switch between
pre-fader (send the pre-fader signal to the bus) and
post-fader (send the post-fader signal to the bus).
L
PAN/BALANCE knob
Move the cursor to this knob and turn the [DATA/
JOG] dial to adjust the pan (or balance, in the case
of the stereo output channel) of the signal that is
sent from the channel to the stereo bus or L/R bus.
JOG] dial to adjust the pan (or balance, in the case
of the stereo output channel) of the signal that is
sent from the channel to the stereo bus or L/R bus.
M
FADER knob (except for the stereo output
channel)
channel)
Move the cursor to this knob and turn the [DATA/
JOG] dial to adjust the level of the signal that is sent
from the channel to the stereo bus or L/R bus. The
range is –
JOG] dial to adjust the level of the signal that is sent
from the channel to the stereo bus or L/R bus. The
range is –
∞
to +6 dB.
Note
Note
The FADER knob of a track channel will follow the opera-
tion of the corresponding panel fader 1–8 or 9/10–15/16.
However, please note that if you adjust an on-screen
knob and then operate the panel fader, the value will not
change until the fader passes the current value.
tion of the corresponding panel fader 1–8 or 9/10–15/16.
However, please note that if you adjust an on-screen
knob and then operate the panel fader, the value will not
change until the fader passes the current value.
N
OUTPUT LEVEL (only for the stereo output
channel)
channel)
Move the cursor to this knob and turn the [DATA/
JOG] dial to adjust the output level of the signal that
is sent from the stereo output channel to the STE-
REO/AUX OUT jacks and MONITOR OUT jacks.
The range is –
JOG] dial to adjust the output level of the signal that
is sent from the stereo output channel to the STE-
REO/AUX OUT jacks and MONITOR OUT jacks.
The range is –
∞
to 0 dB.
Note
Note
The OUTPUT LEVEL knob will follow the operation of
the panel [STEREO FADER]. However, please note that if
you adjust the on-screen knob and then operate the panel
fader, the value will not change until the fader passes the
current value.
the panel [STEREO FADER]. However, please note that if
you adjust the on-screen knob and then operate the panel
fader, the value will not change until the fader passes the
current value.
Initializing a channel
The mix parameters (EQ, dynamics, pan, etc.) of a chan-
nel can be reset to their default settings in a single opera-
tion. This function lets you start mixdown or bounce
operations with the track channels “zeroed,” and pro-
vides an easy way to reset the levels back to the nominal
setting if you can no longer hear any sound.
nel can be reset to their default settings in a single opera-
tion. This function lets you start mixdown or bounce
operations with the track channels “zeroed,” and pro-
vides an easy way to reset the levels back to the nominal
setting if you can no longer hear any sound.
1
In the Quick Navigate section, repeatedly
press the [MONITOR] key or hold down the
[MONITOR] key and use the CURSOR [
press the [MONITOR] key or hold down the
[MONITOR] key and use the CURSOR [
]/
[
] keys to access the INIT page.
In this page you can separately initialize the mix
parameters of input channels 1–8, pad channels 1–
4, or track channels 1–16.
parameters of input channels 1–8, pad channels 1–
4, or track channels 1–16.
2
Press the [INPUT SEL] key, pad, or [TRACK
SEL] key for the channel that you want to ini-
tialize.
SEL] key for the channel that you want to ini-
tialize.
When you press a key or pad, the upper line of the
screen will indicate “CH.PARAMETER INITIAL-
IZED,” and the corresponding channel will be ini-
tialized. (Channel library 00 will be recalled.)
An initialized channel will have the following mix
parameter settings.
screen will indicate “CH.PARAMETER INITIAL-
IZED,” and the corresponding channel will be ini-
tialized. (Channel library 00 will be recalled.)
An initialized channel will have the following mix
parameter settings.
Input channel
Pad channel
Track channel
Phase
no change
no change
no change
Attenuation
0 dB
0 dB
0 dB
EQ
ON
ON
ON
EQ parameters
flat
flat
flat
Dynamics on/off
OFF
OFF
OFF
Dynamics type
COMP
COMP
COMP
Dynamics
parameters
parameters
no effect
no effect
no effect
Pan
If paired: L channel = L16,
R channel = R16
If unpaired: center
R channel = R16
If unpaired: center
L channel = L16
R channel = R16
R channel = R16
If paired: L channel = L16,
R channel = R16
If unpaired: center
R channel = R16
If unpaired: center
Fader
0 dB
*
0 dB
no change
*
* If FADER FLIP is set to TRACK in the UTILITY screen PREFER page.