Yamaha EMX3000 Manual Do Utilizador
8
Front and rear panel
EMX3000—Owner’s Manual
Rear panel
1
SPEAKERS (speaker output) jacks
Speakers can be connected to these jacks.
Speakers can be connected to these jacks.
The type of signals output, the number of speak-
ers you can connect, and acceptable impedance
differ depending on the setting of the Power amp
select switch (control panel V).
ers you can connect, and acceptable impedance
differ depending on the setting of the Power amp
select switch (control panel V).
■ When the Power amp select switch is set
to ST1 L-ST1 R or MONI 1-MONO:
• Two-channel connection
You can connect one or two speakers to each of
the L/MONI1 and R/MONO jacks.
the L/MONI1 and R/MONO jacks.
When the Power amp select switch is set to ST1
L-ST1 R, the speakers connected to the L/MONI1
and R/MONO jacks will output the ST1 L and
ST1 R bus signals. When the switch is set to
MONI 1-MONO, the speakers will output the
MONITOR 1 signal and the MONO signal
respectively.
L-ST1 R, the speakers connected to the L/MONI1
and R/MONO jacks will output the ST1 L and
ST1 R bus signals. When the switch is set to
MONI 1-MONO, the speakers will output the
MONITOR 1 signal and the MONO signal
respectively.
Whichever way the switch is set to, connect 4~8
Ω
speakers if you use one speaker per channel. The
maximum output is 300W+300W with two 4
maximum output is 300W+300W with two 4
Ω
speakers.
• Two-channel parallel connection
If you wish to use two speakers per channel, use
8~16
8~16
Ω
speakers. The maximum output is
300W+300W with 8
Ω
impedance.
■ When the Power amp select switch is set
to MONO (BRIDGE):
• Bridge connection
If you are connecting a single speaker to the
BRIDGE jack, use a 8~16
BRIDGE jack, use a 8~16
Ω
speaker. The speaker
outputs the MONO bus signal, and the maxi-
mum output is 600W with 8
mum output is 600W with 8
Ω
impedance.
If you wish to input the signal from the P.AMP
IN jack, input it from the P.AMP IN L jack.
IN jack, input it from the P.AMP IN L jack.
2
POWER switch
This switch turns on/off the power to the
EMX3000.
This switch turns on/off the power to the
EMX3000.
3
AC inlet
Connect the socket end of the included AC cable
to this inlet. Connect the plug end of the cable to
an AC outlet of the voltage printed below the
inlet.
Connect the socket end of the included AC cable
to this inlet. Connect the plug end of the cable to
an AC outlet of the voltage printed below the
inlet.
AC IN
2
1
2
1
BRIDGE
ON OFF
R/
MONO
L/
MONI 1
SPEAKERS
POWER
2
3
1
Caution:
When using a two-channel connection or
two-channel parallel connection, do not con-
nect a speaker to the BRIDGE jack.
When using a bridge connection, do not con-
nect a speaker to either the L/MONI1 or R/
MONO jacks.
The BRIDGE jack is covered by a protective
cap to prevent you from accidentally connect-
ing a speaker it when using a two-channel or
two-channel parallel connection. Remove
this cap if you are using a bridge connection.
When using a two-channel connection or
two-channel parallel connection, do not con-
nect a speaker to the BRIDGE jack.
When using a bridge connection, do not con-
nect a speaker to either the L/MONI1 or R/
MONO jacks.
The BRIDGE jack is covered by a protective
cap to prevent you from accidentally connect-
ing a speaker it when using a two-channel or
two-channel parallel connection. Remove
this cap if you are using a bridge connection.
Note: Before you turn the power of the
EMX3000 on or off, the faders and controls in
the master section of the control panel must be
lowered to the minimum position.
EMX3000 on or off, the faders and controls in
the master section of the control panel must be
lowered to the minimum position.