Yamaha EMX66M Manual Do Utilizador
Front and rear panel
9
EMX66M—Owner’s Manual
Front and rear panel
Control panel
■
Channel section
In this section, you can adjust equalization (fre-
quency response), volume level, effect and moni-
tor output levels for the input signal of each
channel.
quency response), volume level, effect and moni-
tor output levels for the input signal of each
channel.
1
Equalizer controls (HIGH, MID, LOW)
This is a 3-band equalizer that adjusts the high
frequency range, mid frequency range, and low
frequency range of each channel. Response is flat
when the knobs are in the “
frequency range, mid frequency range, and low
frequency range of each channel. Response is flat
when the knobs are in the “
▼
” position. Rotating
it toward the right will boost the corresponding
frequency band, and rotating it toward the left
will cut it.
The base frequency (or center frequency), range
of boost or cut, and equalizer type of each band
are as follows.
frequency band, and rotating it toward the left
will cut it.
The base frequency (or center frequency), range
of boost or cut, and equalizer type of each band
are as follows.
HIGH:
10 kHz
±15 dB shelving type
MID:
2.5 kHz ±15 dB peaking type
LOW:
100 Hz
±15 dB shelving type
2
Monitor control (MONITOR)
For each channel, this controls the amount of sig-
nal that is sent to the MONITOR bus.
The signal of the MONITOR bus is sent to the
speakers connected to the SPEAKERS B 1/2 jacks
(only if the power amp select switch is in the
MAIN-MON position) and to the MONITOR
jacks (input/output panel
nal that is sent to the MONITOR bus.
The signal of the MONITOR bus is sent to the
speakers connected to the SPEAKERS B 1/2 jacks
(only if the power amp select switch is in the
MAIN-MON position) and to the MONITOR
jacks (input/output panel
6
).
3
Effect control (EFFECT)
For each channel, this controls the amount of sig-
nal that is sent to the EFFECT bus.
The signal of the EFFECT bus is sent to the built-
in effect and to the EFFECT OUT jacks (input/
output panel
nal that is sent to the EFFECT bus.
The signal of the EFFECT bus is sent to the built-
in effect and to the EFFECT OUT jacks (input/
output panel
3
).
4
Level control (LEVEL)
This control adjusts the level of signals routed
from each channel to the MAIN bus and to the
built-in power amplifier.
The MAIN bus signal is sent to the MAIN jacks
(input/output panel
from each channel to the MAIN bus and to the
built-in power amplifier.
The MAIN bus signal is sent to the MAIN jacks
(input/output panel
6
) and the SPEAKERS jacks
on the rear panel
1
.
5
Pad switch (PAD) (Channel 1–4 only)
This switch attenuates the input signal by 30 dB.
When connecting a line level device to channels
1–4, or if the mic input is distorted, turn this
switch on (the pressed-in position).
When connecting a line level device to channels
1–4, or if the mic input is distorted, turn this
switch on (the pressed-in position).
1
PAD
–15
+15
1
HIGH
MID
LOW
LEVEL
MONITOR
EFFECT
–15
+15
–15
+15
0
+15
0
+15
0
10
1
2
3
4
5
Note:
The signal is sent to the MONITOR bus
from a location before the level control (
4
) of
each channel. This means that it will not be af-
fected by the setting of the LEVEL control.
fected by the setting of the LEVEL control.
Note:
The signal is sent to the EFFECT bus
from a location after the level control (
4
) of
each channel. This means that the amount of
signal that is sent to the EFFECT bus will be af-
fected not only by the setting of the effect con-
trol, but also by the setting of the level control.
signal that is sent to the EFFECT bus will be af-
fected not only by the setting of the effect con-
trol, but also by the setting of the level control.