Yamaha RX-V2300 Manual Do Utilizador
45
English
INTR
ODUCTION
PREP
ARA
TION
B
ASIC OPERA-
TION
AD
V
ANCED
OPERA
TION
ADDITIONAL
INFORMA
TION
APPENDIX
REMOTE CONTROL FEATURES
LEARN
5
Press LEARN again to exit from the setup
mode.
mode.
Notes
• Supplied remote control does not store all the manufacturer
codes for commercially availabvle AV components (including
Yamaha AV components). Therefore it may not work to operate
your AV component. If operation is not possible with any of the
manfacturer codes, program the new remote control function
with the Learn feature (see page 45) or use the remote control
for the component.
Yamaha AV components). Therefore it may not work to operate
your AV component. If operation is not possible with any of the
manfacturer codes, program the new remote control function
with the Learn feature (see page 45) or use the remote control
for the component.
• If you have already programmed a remote control function for a
button, the function by learning programming takes priority
over the setup manufacturer code’s function.
over the setup manufacturer code’s function.
• “ERROR” appears in the display window when pressing
buttons other than indicated in each step, or more than one
button at once.
button at once.
Learn Feature
If you want to program functions not included in the basic
operations covered by the manufacturer code, or a
manufacturer code is not available, the following
procedure needs to be performed. The possible
programming area is the same as a component control
area, so the buttons are programmable independently for
each source component area.
operations covered by the manufacturer code, or a
manufacturer code is not available, the following
procedure needs to be performed. The possible
programming area is the same as a component control
area, so the buttons are programmable independently for
each source component area.
Note
• This remote control transmits infrared rays. If the other remote
control also uses infrared rays, this remote control can learn
most of the other remote control’s functions. However, you
may not be able to program some special signals or extremely
long transmissions. (Refer to the operation instructions for the
other remote control.)
most of the other remote control’s functions. However, you
may not be able to program some special signals or extremely
long transmissions. (Refer to the operation instructions for the
other remote control.)
■ Programming a new remote
control function
1
Set 10KEY/DSP to 10KEY.
Notes
• It is also possible to program in the control area of this unit
with 10KEY/DSP set to DSP. However, if you program
functions in this area, you cannot control this unit and select a
DSP program.
functions in this area, you cannot control this unit and select a
DSP program.
2
Press an input selector button, Å or ı to
select a source component.
select a source component.
5 to 10 cm (2 to 4 inch)
TRANSMIT
RE-NAME
ST
ANDBY
6CH INPUT
SYSTEM
CLEAR
LEARN
MA
CR
O
OFF
ON
MA
CR
O
PHONO
A
B
CD
DV
D
VCR2/D
VR
VCR 1
TITLE
SOURCE
ENTER
D-TV/LD
CBL/SA
T
CD-R
MD/T
APE
TUNER
V-
A
A
U
X
PO
WER
LEARN
DSP
10KEY
Flashes alternately
PHONO
A
B
CD
DVD
VCR2/DVR
VCR 1
D-TV/LD
CBL/SAT
CD-R
MD/TAPE
TUNER
V-AUX
3
Place this remote control and the other
remote control about 5 to 10 cm apart on a
flat surface so that their infrared transmitters
are aimed at each other.
remote control about 5 to 10 cm apart on a
flat surface so that their infrared transmitters
are aimed at each other.
4
Press LEARN by using a ballpoint pen or
similar object.
Do not press and hold LEARN longer than three
seconds. Otherwise this unit enters the manufacturer
code setting mode.
similar object.
Do not press and hold LEARN longer than three
seconds. Otherwise this unit enters the manufacturer
code setting mode.
Notes
• Complete each of the following steps in 30 seconds. Otherwise,
the learning mode will be automatically canceled. In this case,
press LEARN again.
press LEARN again.
• Do not press and hold LEARN longer than 3 seconds.
Otherwise this unit enters the manufacturer code setting mode.
5
Press the button for which you want to
program the new function.
“LEARN” is displayed.
program the new function.
“LEARN” is displayed.
TRANSMIT
RE-NAME
ST
ANDBY
6CH INPUT
SYSTEM
CLEAR
LEARN
MA
CR
O
OFF
O
N
MA
CR
O
PHONO
A
B
CD
DV
D
VCR2/D
V
R
VCR 1
TITLE
SOURCE
ENTER
D-TV/LD
CBL/SA
T
CD-R
MD/T
APE
TUNER
V-
A
A
U
X
PO
WER
0108V2300_43-56_EN(U)
02.8.9, 10:38 AM
45