Yamaha yamaha stereo amplifier dsp-e492 Manual Do Utilizador
8
CONNECTIONS
REAR PANEL PARTS AND THEIR FUNCTIONS
MONITOR
OUT
DVD/LD
TV/DBS
IN
OUT
VCR
VIDEO SIGNAL
CD
(LINE 1)
TAPE
( MD )
DVD/LD
TV/DBS
VCR
TAPE
PB
REC
OUT
OUT
IN
OUT
AUDIO SIGNAL
1
3
4
MAIN
TUNER
(LINE 2)
2
MAINS
SPEAKERS
OUTPUT
INPUT
OUTPUT
l0 dB 0 dB
l
MAIN
LEVEL
SINGLE:8
Ω
MIN./SPEAKER
DUAL:4
Ω
MIN./SPEAKER
8
Ω
MIN./SPEAKER
CENTER
REAR
SINGLE:4
Ω
MIN./SPEAKER
DUAL:2
Ω
MIN./SPEAKER
6
Ω
MIN./SPEAKER
CENTER
REAR
IMPEDANCE SELECTOR
REAR
CENTER
SUB
WOOFER
DUAL
(SURROUND)
DUAL
CAUTION
SEE INSTRUCTION MANUAL FOR CORRECT SETTING.
DUAL
DUAL
SINGLE
REAR
CENTER
I00W MAX.
SWITCHED
AC OUTLET
6CH DISCRETE
INPUT
REAR
CENTER
MAIN
SUB
WOOFER
(SURROUND)
(SURROUND)
REAR
CENTER
MAIN
SUB
WOOFER
INPUT
from
AMP/RECEIVER
PREOUT
from
AMP/RECEIVER
PREOUT
1
8
9
0
A
B
C D
2
3
4
5
6
7
1
6CH DISCRETE INPUT terminals
Connect a Dolby Digital (AC-3) Decoder to these terminals.
6-channels (left main, right main, center, left rear surround,
right rear surround and subwoofer) of discrete audio signals
with the Dolby Digital (AC-3) decoded are input to these
terminals from the decoder.
6-channels (left main, right main, center, left rear surround,
right rear surround and subwoofer) of discrete audio signals
with the Dolby Digital (AC-3) decoded are input to these
terminals from the decoder.
2
INPUT (from AMP/RECEIVER PREOUT) terminals
These are additional 6-channel audio signal input terminals (for
left main, right main, center, left rear surround, right rear
surround and subwoofer channels) available for inputting
signals from your existing amplifier, receiver, sound processor,
etc. to this unit.
To listen to a sound by reproducing signals input to these
terminals from the external amplifier etc., be sure to set the
PROCESSOR SELECTOR switch on the front panel to the
“EXTERNAL” position. By doing so, the signals input to these
terminals are sent to the corresponding SPEAKERS terminals
and OUTPUT terminals of this unit bypassing any circuit in this
unit. So, volume, tone, etc. must be controlled on the external
amplifier.
left main, right main, center, left rear surround, right rear
surround and subwoofer channels) available for inputting
signals from your existing amplifier, receiver, sound processor,
etc. to this unit.
To listen to a sound by reproducing signals input to these
terminals from the external amplifier etc., be sure to set the
PROCESSOR SELECTOR switch on the front panel to the
“EXTERNAL” position. By doing so, the signals input to these
terminals are sent to the corresponding SPEAKERS terminals
and OUTPUT terminals of this unit bypassing any circuit in this
unit. So, volume, tone, etc. must be controlled on the external
amplifier.
3
MAIN OUTPUT terminals
Main-channel line output. Connect these to input terminals of
external stereo power amplifier (MAIN IN or equivalent
terminals of integrated amplifier or receiver) driving the main
speakers.
external stereo power amplifier (MAIN IN or equivalent
terminals of integrated amplifier or receiver) driving the main
speakers.
4
IMPEDANCE SELECTOR switch
Select the position whose requirements your speaker system
meets.
Be sure to switch this only when the power of this unit is turned
off.
meets.
Be sure to switch this only when the power of this unit is turned
off.
(Right position)
Center: If you use one center speaker, the impedance of
the speaker must be 8
Ω
or higher.
If you use two center speakers, the impedance of
each speaker must be 4
each speaker must be 4
Ω
or higher.
Rear:
The impedance of each speaker must be 8
Ω
or
higher.
(Left position)
Center: If you use one center speaker, the impedance of
the speaker must be 4
Ω
or higher.
If you use two center speakers, the impedance of
each speaker must be 2
each speaker must be 2
Ω
or higher.
Rear:
The impedance of each speaker must be 6
Ω
or
higher.
WARNING
Do not change the IMPEDANCE SELECTOR switch
setting while the power to this unit is on, otherwise this
unit may be damaged.
Do not change the IMPEDANCE SELECTOR switch
setting while the power to this unit is on, otherwise this
unit may be damaged.
INTERNAL
EXTERNAL
PROCESSOR
SELECTOR
(Europe model)