Sanyo avp504 Manual Do Utilizador
Channel selection
Information about USA and Canadian channel numbering
+
Method 1 — Using the Channel up/down buttons (CH+ or CH-)
Press the CH+ or CH- to cycle among available channels found (while the hided channels can not be selected).
Press the number buttons (0-9) and the Dot (.) button, then wait for the television to change channels or press ENTER to go
immediately to that channel.
For example, if you want to select channel 8.3, just key in ‘8’, ‘.’, ‘3’ on the remote control.(Be sure the period of two-press
should be within 3 seconds)
immediately to that channel.
For example, if you want to select channel 8.3, just key in ‘8’, ‘.’, ‘3’ on the remote control.(Be sure the period of two-press
should be within 3 seconds)
=When you use the number buttons, you can directly select any channel within the channel range .
=In some situations virtual channel numbers have no correspondence to physical frequencies.
=To select an analog channel, you may directly input its major channel number. It is unnecessary to input the minor channel number of zero.
=In some situations virtual channel numbers have no correspondence to physical frequencies.
=To select an analog channel, you may directly input its major channel number. It is unnecessary to input the minor channel number of zero.
Press this button to switch between the current channel and the last viewed channel.
Channel Selection
=
ATSC PSIP channel has two part channel number:
—
Major channel number
— Minor channel number
=
In most situations the major channel number is same for both analog and digital channels (It is equal to the NTSC channel
number for existing broadcasters.)
=
Usually a minor channel number of zero is used for a broadcaster’s analog channel.
Channel Numbering Example
=
Original NTSC Channels for Des Moines:
—
5, 8, 11, 13, 17
=
Possible NTSC + ATSC Channels for Des Moines:
— 5-0, 8-0, 11-0, 13-0, 17-0 (channel numbers for existing analog channels)
— 5-1, 5-2, 8-1, 8-2, 8-3,8-4, 13-1 (channel numbers for digital channels)
After auto-search, a default channel list has been created. You may press CH.LIST button
to call up the channel list, then make use of 6or5 to select the channel, then wait for
some seconds or press ENTER to go directly to that program. If the channel list has more
than one page, you can press 3or4to scroll the page.
to call up the channel list, then make use of 6or5 to select the channel, then wait for
some seconds or press ENTER to go directly to that program. If the channel list has more
than one page, you can press 3or4to scroll the page.
If you have created your favorite program list, you may press FAVORITE button to call up
the favorite list, then make use of 6or5 to select the channel, then wait for some seconds
or press ENTER to go directly to that program. If the program list has more than one page,
you can press 3or4to scroll the page.
the favorite list, then make use of 6or5 to select the channel, then wait for some seconds
or press ENTER to go directly to that program. If the program list has more than one page,
you can press 3or4to scroll the page.
For example:
Channel: 5.1
Major channel number
Minor channel number
Note
You can select your desired TV program by one of the following methods.
+
Method 2 — Using the direct select buttons (0-9 and Dot buttons)
+
Method 3 — Using the RECALL button
+
Method 4 — Using the Channel List or Favorite List
21
1.2 Sencore
2.0
2.1 WGBH-SD
2.2 PBS-HD
2.0
2.1 WGBH-SD
2.2 PBS-HD
6.0
7.0
11.1 MBC DTV
12.0
14.0
7.0
11.1 MBC DTV
12.0
14.0
Next
NO. NAME
2.3 WGBH-Dx
（
The above OSD is only
for illustration purpose.
The actual screen may vary.)