Symphonic sd7s3 Manual Do Utilizador
– 13 –
EN
1L25
CONNECTING TO A TV WITH A/V TERMINALS
DVD/VCR
VCR
AUDIO OUT
AUDIO IN
VIDEO OUT
VIDEO IN
S-VIDEO
OUT
COMPONENT
VIDEO OUT
AUDIO
OUT
DVD
Y
Cb
L
Cr
R
ANT-IN
ANT-OUT
L
R
DIGITAL
AUDIO OUT
COAXIAL
To VIDEO OUT jack
To VIDEO INPUT jack
To Right (red) and Left (white)
Antenna/Cable signal
To ANT. IN
of TV
To AUDIO INPUT jacks To AUDIO OUT jacks
A/V-compatible or
wide screen TV
[Fig. 1]
Notes
¡
Connect the DVD/VCR COMBINATION UNIT directly to a TV. If the A/V cables are connected into a
VCR first, picture may be distorted due to the copy protection system.
VCR first, picture may be distorted due to the copy protection system.
CONNECTING TO A TV WITHOUT A/V TERMINALS
1. Disconnect the AC power cord of the TV from the
AC outlet.
2. Disconnect the antenna or cable from the TV.
3. Connect the antenna or cable to the ANT-IN jack of
3. Connect the antenna or cable to the ANT-IN jack of
the DVD/VCR COMBINATION UNIT.
4. Connect the DVD/VCR COMBINATION UNIT to
the TV using the RF cable.
5. Plug the AC power cords of the DVD/VCR COM-
BINATION UNIT and TV into the AC outlets.
UHF/VHF
DVD/VCR
VCR
AUDIO OUT
AUDIO IN
VIDEO OUT
VIDEO IN
L
R
[VHF/UHF
combination antenna]
combination antenna]
[Back of the DVD/VCR]
IN
OUT
[Cable box or satellite box]
OR
[Indoor antenna]
[Back of the
UHF/VHF combination TV]
RF cable
(supplied)
(supplied)
From Cable or
Satellite Company
Satellite Company
OR
ANT-IN
ANT-OUT
Note to CATV system installer
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that pro-
vides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected
to the grounding system of the building, as close to the point of cable entry as practical.
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that pro-
vides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected
to the grounding system of the building, as close to the point of cable entry as practical.
HOOKUPS
CAUTION:
¡
Be sure to turn off the DVD/VCR COMBINATION UNIT and equipment to be connected.
¡
Read through the operation manual for the equipment to be connected.
¡
Be sure that the colors of the jacks and plugs match up when using VIDEO/AUDIO cables.
¡
Be sure to keep the DVD/VCR COMBINATION UNIT connection cables separate from the TV antenna cable
when you install the DVD/VCR COMBINATION UNIT, because it may cause electrical interference when you
are watching television programs.
when you install the DVD/VCR COMBINATION UNIT, because it may cause electrical interference when you
are watching television programs.
RF OUTPUT CHANNEL for DVD/VCR
1. Connect the DVD/VCR COMBINATION UNIT to a TV using RF cable (see above steps).
2. Select channel 3 on your TV.
3. Press PLAY.
2. Select channel 3 on your TV.
3. Press PLAY.
¡
If noise appears, change the RF output channel of the DVD/VCR COMBINATION UNIT to channel 4 by
pressing PLAY on the VCR for 3 seconds during playback.
pressing PLAY on the VCR for 3 seconds during playback.
¡
There is case that the RF output channel does not change by situation (For example, when you adjust tracking using
CHANNEL
CHANNEL
).
In this case, stop the playback, and start the playback again. After that, press PLAY on the VCR for 3 seconds.
¡
If there is a power failure or the DVD/VCR COMBINATION UNIT is unplugged for more than 30 seconds, the RF
output channel setting will return to CH3.
output channel setting will return to CH3.
( )
H94A3UD.QX3 03.8.20 11:43 AM Page 13