temco-tool 36tdvn Manual Do Utilizador
23
TDVN Series Direct Vent Gas Fireplace
20007636
Unpack the logs from packaging and remove each log
from its wrapping materials.
from its wrapping materials.
The logs are fragile and should be handled
with care. Keep the packaging material out
of the reach of children and dispose of the
material in a safe manner.
with care. Keep the packaging material out
of the reach of children and dispose of the
material in a safe manner.
The embers supplied with your fireplace
are made from a high grade rock wool and
should be handled carefully. Wash your
hands immediately after touching to avoid
are made from a high grade rock wool and
should be handled carefully. Wash your
hands immediately after touching to avoid
irritation. The embers must be placed
correctly in order to function properly.
correctly in order to function properly.
Installation of Logs, Lava Rock & Ember Material
Log Installation
Attention: Glass door should be removed when install-
ing logset and prior to lighting the unit.
1. Remove glass door (Refer to “Window Frame).
2. Remove logs from carton and inspect. Refer to Fig-
ing logset and prior to lighting the unit.
1. Remove glass door (Refer to “Window Frame).
2. Remove logs from carton and inspect. Refer to Fig-
ure 39.
3. Rear log should be installed onto rear log supports.
Match up slots on rear of log with the vertical log
bracket tabs. Push log back as far as it will go.
bracket tabs. Push log back as far as it will go.
4. The center log should be placed on the center log
supports, slots aligned with tabs and log placed rear-
ward.
ward.
5. Top twigs can then be placed in their designated po-
sitions provided with pins on back logs and grooves
on the center log.
on the center log.
6. Place platinum embers loosely along top surface
of burner along entire length of ported area of front
burner. DO NOT place embers on back portion of
burner. Use individual pieces of embers no larger
than dime size, about 1/16” thick (fluffed up thick-
ness). Use a single layer of embers and DO NOT
overlap pieces. Ember material should be fluffed up
and not compressed. When properly placed, all em-
bers will glow red. Adding more embers than neces-
sary will detract from appearance.
burner. DO NOT place embers on back portion of
burner. Use individual pieces of embers no larger
than dime size, about 1/16” thick (fluffed up thick-
ness). Use a single layer of embers and DO NOT
overlap pieces. Ember material should be fluffed up
and not compressed. When properly placed, all em-
bers will glow red. Adding more embers than neces-
sary will detract from appearance.
7. Ember tray ends beyond burner port area and area
in front of grate may be covered with lava rock to
suit individual appearance preferences.
suit individual appearance preferences.
8. Purge lines and test pilot operation.
9. Replace glass door. The door must be installed be-
9. Replace glass door. The door must be installed be-
fore operating the fireplace.
10. Flame should not impinge (touch) on logs.
WARNING: Do not place lava rock or any
other materials on the burner. Use only certi-
fied material supplied with this fireplace. Using
uncertified materials will void the warranty.
other materials on the burner. Use only certi-
fied material supplied with this fireplace. Using
uncertified materials will void the warranty.
TL119
DV1000/DV1200
logs
12/11/03 djt
TL119
Fig. 39 Correct log placement. 36TDVN shown.
TL121
DV1000/DV1200
final position logs
12/11/03 djt
TL121
Fig. 40 Logs in final position. 36TDVN shown.
TL122
Dv logs
side view
12/11/03 djt
Back Log
Slot
Bracket
Bracket
Twig
Front Log
TL122
Fig. 41 Side view of logset.