Edelbrock performer rpm 63-0046 Manual Do Utilizador
Page 2
©2004 Edelbrock Corporation
Brochure # 63-0046
Rev. 7/04
Edelbrock Corporation • 2700 California St. • Torrance, CA 90503
Tech Line: (800) 416-8628 • Tech Fax: (310) 972-2730
E-Mail: Edelbrock@Edelbrock.com
SPECIFICATIONS
Head bolt torque: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
65 ft./lbs. (short bolts; #11, #5, #4, and #10),
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
75 ft./lbs. (long bolts; all others)
Rocker stud torque: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
45 ft./lbs.
Combustion chamber volume: . . . . . . . . . . . . . . . . . . . . . . . . . . .
118 cc
Deck thickness: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9/16"
Valve Seats: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hardened, interlocking, compatible with unleaded fuels
Valve Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intake- 2.19", Exhaust- 1.88"
Valve Stem Diameter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11/32"
Valve Spring Diameter: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.54"
Valve Spring Installed Height: . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.975"
Valve Spring Pressure: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
120 lbs. @ 1.975
Max. Valve Lift: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.700"- Check spring pressures per cam manufacturer.
PLEASE complete and mail your warranty card. Be sure to write the model number of this product in the “Part #____” space. THANK YOU.
Bolt Boss Height
A = 3.38”
B = 2.88”
C = 4.44”
D = 1.38”
INSTALLATION: Installation is the same as for original equipment
cylinder heads. Consult service manual for specific procedures, if
necessary. For 454 and smaller Mark IV engines, use Edelbrock head
gasket #7302, Fel-Pro head gasket #1017-1 or equivalent. For 454
Gen V engines, use Fel-Pro head gasket #1037, or equivalent. For 502
c.i.d. Gen V engines, use Fel-Pro head gasket #1047 or equivalent.
cylinder heads. Consult service manual for specific procedures, if
necessary. For 454 and smaller Mark IV engines, use Edelbrock head
gasket #7302, Fel-Pro head gasket #1017-1 or equivalent. For 454
Gen V engines, use Fel-Pro head gasket #1037, or equivalent. For 502
c.i.d. Gen V engines, use Fel-Pro head gasket #1047 or equivalent.
NOTE: For 454 and smaller Mark IV engines, Edelbrock Cylinder Head
Gasket Set #7362 may be used.
Gasket Set #7362 may be used.
The set contains all gaskets
necessary to install these cylinder heads onto a Mark IV engine,
including intake, exhaust, cylinder head, distributor, water neck, and
valve cover gaskets.
including intake, exhaust, cylinder head, distributor, water neck, and
valve cover gaskets.
Figure 1
Be sure that the surface of the block and the surface of the head is
thoroughly cleaned to remove any oily film before installation. Use
alcohol or lacquer thinner on a lint-free rag to clean. Apply liquid teflon
or suitable thread sealer to head bolt threads. Torque short bolts to 65
ft./lbs. and long ones to 75 ft./lbs. in three steps following the factory
tightening sequence (see Figure 1). A re-torque is recommended after
initial start-up and cool-down (allow 2-3 hours for adequate cooling.
thoroughly cleaned to remove any oily film before installation. Use
alcohol or lacquer thinner on a lint-free rag to clean. Apply liquid teflon
or suitable thread sealer to head bolt threads. Torque short bolts to 65
ft./lbs. and long ones to 75 ft./lbs. in three steps following the factory
tightening sequence (see Figure 1). A re-torque is recommended after
initial start-up and cool-down (allow 2-3 hours for adequate cooling.