Epson 850 Manual Do Utilizador
LQ - 850/950/1050 DOT- MATRIX PRINTER
The Cut Sheet Feeder
The following a
example of a software setup
for
proper operation of your cut sheet feeder. Not all software is
up
the
you may find that a
of
required
you
best equivalent settings to use.
To
54
per page:
Cut sheet
form
feeder
Change Page
Length from
6 1
Change Top
Margin from
4
Change
Bottom
Margin from
6
to
3
Many word processors and other software
you
ways to
change these
l
You can change the settings in each individual file you print or;
l
You can change the program’s default settings so that every time
you use the program, these new settings are in effect.
If your program has additional features, such as headers and
footers, you have to compensate accordingly.
Control panel operation
All of the
from the control panel are
cut sheet
feeder mode.
adjustment of the
after loading a sheet using the LOAD/EJECT button and
the ON LINE button.
sets a new sheet loading
for as long as the power
on. If the power
IS
turned
off. the loading
returned to the factory
Changing
the
with
adjustment affects the number of lines
per page. You may need change your software margin settings
for
new page length.
The optional cut sheet feeders
you easier and more efficient
handling of
sheet paper Up to 150 sheets of standard bond
paper can be fed automatically into the printer without reloading.
These
These
can also automatically feed envelopes.
Printer
Single bin
LQ-850
LQ-950
LQ-
LQ-950
LQ-
Dual bin
The
this chapter show the
bin feeder for the
LQ-1050. but the others work in the same way. For the dual bin
feeders, see the manual that comes with them for assembly
instructions. You can select the second bin with a software command
(ESC EM) or the control panel.
instructions. You can select the second bin with a software command
(ESC EM) or the control panel.
paper support
paper feeder rests
LQ - 850/950/1050 - 4
front stacker
1 2 / 1 2 / 8 8
After checking to see that you have all of the parts shown in the
figure above, remove the foam packaging from between the paper
rests and rollers. Keep the packing materials in the original box in
case you need to store or transport the cut sheet feeder.
case you need to store or transport the cut sheet feeder.
I n
I
The
pull tractor (A731 for the LQ-850,
for the
LQ-950. or
for the LQ-1050) provides
paper handling. The pull tractor
IS
especially
continuous
multi-part forms and labels. For best results, use the pull
along with the
push tractor. as described in this section.
After making sure that you have both parts of the
tractor
option as shown below, remove the packing material and save it in
case you need to ship the unit later.
case you need to ship the unit later.
pull tractor cover
!
The short tear-off function cannot be used with the pull
tractor. Before you start printing with the pull tractor,
make sure that DIP switch 2-7 is set to off. (See the
section
make sure that DIP switch 2-7 is set to off. (See the
section
on setting DIP switches in Chapter 3.)
The Multi Font Module
The optional Multi-Font Module
gives you seven
additional fonts for your LQ printer. Once you install it in either slot
A or slot B, the following fonts are available: Courier, Prestige,
Script, OCR-A, OCR-B, Orator, and Orator-S.
A or slot B, the following fonts are available: Courier, Prestige,
Script, OCR-A, OCR-B, Orator, and Orator-S.
The Multi-Font Module is installed in one of the slots (A or B)
the printer. See the manual that comes with the module for full
information on using the font module.
information on using the font module.
Using the Multi-Font
Module
To install a font module, follow these steps:
1. Make sure the printer is turned off.
2. Open the font compartment cover. Inside the compartment are
two connectors
A and
24 - Pin Printers