Kenwood KTC-1000R Manual Do Utilizador
Troubleshooting Guide
English
9
PROBLEM
POSSIBLE CAUSE
SOLUTION
The sound quality is poor or
distorted.
distorted.
Radio reception is poor.
The memory is erased when
the ignition is turned off.
the ignition is turned off.
• A speaker cable may be pinched by
a screw in the car.
• The speakers are not cabled
correctly.
• The car antenna is not extended.
• The antenna control cable is not
• The antenna control cable is not
connected.
• Adverse effect of noise from power
cable, etc.
• The battery cable has not been
connected to the proper terminal.
• The ignition and battery cable are
incorrectly connected.
• Check the speaker wiring..
• Reconnect the speaker cables so
that each output terminal is
connected to a different speaker.
connected to a different speaker.
• Pull out the antenna all the way.
• Connect the cable correctly,
• Connect the cable correctly,
referring to the section on
"Connecting Cables to Terminals".
"Connecting Cables to Terminals".
• Be sure to install the antenna cable
away from the power cable.
• Connect the cable correctly,
referring to the section on
"Connecting Cables to Terminals".
"Connecting Cables to Terminals".
• Connect the cable correctly,
referring to the section on
"Connecting Cables to Terminals".
"Connecting Cables to Terminals".
The following indications are used to inform you that there is a problem with the connections
of the system.
of the system.
BUS-E01:
The M-S switch of the Monitor connected to the BUS terminal is set to "M".
] Switch the Monitor’s M-S switch to "S".
The "MASTER SW" cable of the monitor power supply harness is connected to -.
] Do not connect the "MASTER SW" cable.
BUS-E50:
Two or more center units are connected.
BUS-W02:
The No. switch of the connected disc changers is set to the same number (1 or 2) for
both units.
both units.
] Set the No. switch of one disc changer to "1" and the other unit to "2" to enable proper
use.
BUS-W08:
Two or more Monitors are connected to the BUS terminal.
FM tuner section
Frequency range (50 kHz Space)
..............................................87.5 MHz – 108.0 MHz
Usable sensitivity (S/N = 26dB) ..............0.7 µV/75
Ω
Quieting Sensitivity (S/N = 46dB) ............1.6 µV/75
Ω
Frequency response (±3.0 dB) ..........30 Hz – 15 kHz
Signal to Noise ratio (MONO) ..........................65 dB
Selectivity (DIN) (±400 kHz) ........................
Signal to Noise ratio (MONO) ..........................65 dB
Selectivity (DIN) (±400 kHz) ........................
≥
80 dB
Stereo separation (1 kHz) ................................35 dB
MW tuner section
Frequency range (9 kHz Space)
..................................................531 kHz – 1611 kHz
Usable sensitivity (S/N = 20dB) ........................25 µV
LW tuner section
Frequency range ..........................153 kHz – 281 kHz
Usable sensitivity (S/N = 20dB) ........................45 µV
Usable sensitivity (S/N = 20dB) ........................45 µV
Audio section
Maximum output power ..............................44 W
×
4
Output power (DIN 45324, +B=14.4 V) ......28 W
×
4
Tone action
Bass: ......................................100 Hz ±10 dB
Treble:......................................10 kHz ±10 dB
Treble:......................................10 kHz ±10 dB
Preout level / load ..........4 V / 10 k
Ω
(During CD play)
Preout Impedance ..........................................
≤
80
Ω
General
Operating voltage............14.4 V (11 – 16 V allowable)
Current consumption ................10 A at Rated power
Installation size (W
Current consumption ................10 A at Rated power
Installation size (W
×
H
×
D)........213
×
40
×
148 mm
Weight ..............................................................990 g
Specifications subject to change without notice.
Specifications