Philips 20xl Manual Do Utilizador
3
HAIR LENGTH SELECTOR,WITH
GUIDE COMB
GUIDE COMB
IMPORTANT
The Hair Length Selector allows you to adjust to seven
different hair lengths, so that you may achieve the exact
length and look you want.
The Hair Length Selector allows you to adjust to seven
different hair lengths, so that you may achieve the exact
length and look you want.
1
To adjust settings, push Hair Length Selector to
desired setting.
desired setting.
2
Hair Length Selector will “click” and automatically
lock into place at each setting (Fig. 3).
lock into place at each setting (Fig. 3).
•
Start at higher setting (#6 or #7), to prevent
trimming off too much hair.
trimming off too much hair.
•
As you become familiar with the settings, adjust
Hair Length Selector to desired trimming length
(see settings below).
Hair Length Selector to desired trimming length
(see settings below).
SETTINGS
7
leaves hair approximately
21 mm/.84 inches in length
6
leaves hair approximately 18 mm/.72 inches in length
5
leaves hair approximately 15 mm/.6
inches in length
4
leaves hair approximately 13 mm/.52 inches in length
3
leaves hair approximately 10 mm/.4
inches in length
2
leaves hair approximately
7 mm/.28 inches in length
1
leaves hair approximately
4 mm/.16
inches in length
4
5
6
TRIMMING
Before Trimming Hair
1
Be certain Hair Clipper is clean (free of hair and
debris).
debris).
NOTE: If cutter blades are running slowly or do not
move, they may be dirty and clogged.
Clean following MAINTENANCE instructions.
move, they may be dirty and clogged.
Clean following MAINTENANCE instructions.
2
Seat person having hair trimmed so that the top of
their head is at your chest height.
Place towel around their neck.
their head is at your chest height.
Place towel around their neck.
3
Comb hair well to remove all tangles. It is not
necessary to wash hair before trimming. For best
results, use on dry hair.
necessary to wash hair before trimming. For best
results, use on dry hair.
4
For accurate cutting control, hold Hair Clipper in
a comfortable grip.This is important for a precise,
even cut.
a comfortable grip.This is important for a precise,
even cut.
5
For best results, comb hair often during trim to be
certain the cut is even.
certain the cut is even.
6
If using Hair Clipper for the first time, trim only a
small amount of hair at a time, until you become
comfortable with Hair Clipper and the Hair
Length Selector.
small amount of hair at a time, until you become
comfortable with Hair Clipper and the Hair
Length Selector.
IMPORTANT: When using Hair Clipper without
Comb Attachment, use a slow, smooth motion to
prevent trimming off more hair than desired.
Comb Attachment, use a slow, smooth motion to
prevent trimming off more hair than desired.
Trimming Your Hair
1
Use Hair Clipper with Guide Comb.
2
Comb hair so that it falls into its natural direction.
3
Begin at highest setting (#7) on the Hair
Length Selector.
After you are familiar with the Hair Clipper, you
may easily choose between the 7 settings for your
desired length.
Length Selector.
After you are familiar with the Hair Clipper, you
may easily choose between the 7 settings for your
desired length.
4
Hold Hair Clipper with Guide Comb flat against
the scalp (Fig. 4).
the scalp (Fig. 4).
5
Start at the sides of the head. Move Hair Clipper
up slowly against direction of hair, lifting it up and
outward through hair, cutting a small amount at a time.
up slowly against direction of hair, lifting it up and
outward through hair, cutting a small amount at a time.
6
Continue trimming at neck and back of head (Fig. 5).
7
If you want hair shorter, change Hair Length
Selector to a lower setting and follow same steps.
Selector to a lower setting and follow same steps.
Trimming Top Of Head
1
Remove Guide Comb Attachment.
2
Comb hair forward over eyes.
3
Using barber comb, lift a small section of hair at a
time and grasp hair between two fingers.
The amount of hair you wish to cut should extend
beyond your fingers (Fig. 6).
time and grasp hair between two fingers.
The amount of hair you wish to cut should extend
beyond your fingers (Fig. 6).
4
Trim and blend hair using scissors or Hair Clipper.
5
Continue this procedure, working from the front to
the back of head.
As you work to the back, you may gradually cut
hair shorter by holding fingers closer to head when
grasping sections of hair.
the back of head.
As you work to the back, you may gradually cut
hair shorter by holding fingers closer to head when
grasping sections of hair.
6
Comb hair often to remove trimmed hair and to
check for uneven areas.
check for uneven areas.