Maytag bravos w10092823a - sp Manual Do Utilizador

Warm rinses leave the loads drier and more comfortable to handle 

than cold rinses. However, warm rinses also increase wrinkling. 

Cold rinses may help with wrinkling and save energy. 

Whites and pastels

Bright colors

Colors that bleed or fade

NOTE: In wash water temperatures colder than 60°F (15.6°C), 

detergents do not dissolve well. Soils may be difficult to remove.

This washer automatically selects the spin speed based on the cycle 

selected. The preset speeds can be changed. Spin speeds may vary by cycle.

Soil Level (wash time) is preset for each wash cycle. See “Preset 

Cycle Settings” in “Cycles.” As you press the Soil Level pad, 

the cycle time will increase or decrease in the Estimated Time 

Remaining display and a different wash time will appear. To get the 

minimum wash time, press the pad until the indicator light next to 

Light illuminates. This is the shortest wash time available for that 

cycle with the wash options selected.

For most loads, use the time recommended in the preset cycle 

■

■

settings.
For heavy soil and sturdy fabrics, press Soil Level to select more 

■

■

wash time, if needed.
For light soil and delicate fabrics, press Soil Level to select less 

■

■

wash time, if needed.

Auto Temperature Control (ATC) electronically senses and 

maintains a uniform wash and rinse water temperature. ATC 

regulates incoming hot and cold water. The ATC is automatically 

turned On when a cycle is selected. (See “Preset Cycle Settings”  

in “Cycles.”) 

ATC is available with Warm/Warm, Warm/Cold, and Cool/Cold 

settings. The water temperature in the Hot/Cold and Cold/Cold 

settings depends on the water temperature at the water inlet 

faucets.

ATC ensures consistent cleaning.

■

■

Heated water consumes the largest amount of energy that a 

■

■

washer uses.
Today’s detergents work well at temperatures above 60°F 

■

■

(15.6°C).

You can use the Delay Start feature to delay the start of a wash 

cycle for up to 10 hours (depending on your model).

1.  Load the washer and fill the dispensers.
2.  Close the washer lid.
3.  Press POWER/CANCEL.
4.  Select the desired Cycle, Modifiers, and Options. Delay Start 

not valid for Drain & Spin cycle.

5.   Press  + (plus) DELAY START. 1H (one hour) will be displayed 

in the time display window. The indicator light for Delay will 

glow.

6.   For a longer delay time, press DELAY START + (plus). For a 

shorter delay time, press DELAY START – (minus). The Start time 

will increase or decrease by 1-hour steps.

7.   Press START/PAUSE. The countdown in hours and minutes to 

the wash cycle will show in the time display window and the 

indicator light will begin to flash. 

NOTE: The Start/Pause indicator light will not flash when 

Delay Start is chosen. You must press Start/Pause to initiate a 

countdown for the cycle to begin. The cycle selections and 

modifiers are lit during the Delay Start time.

Press POWER/CANCEL once to cancel Delay Start or press START/

PAUSE to cancel the countdown and start the cycle.

Use these pads to select or deselect the options for your wash 

cycle. Options may add time to the wash cycle.

The Water Save Spray Rinse option reduces rinse water in the 

cycle. This option is available on most cycles and must be selected 

prior to the start of the cycle. Do not use liquid fabric softener 

with the Water Save Spray Rinse option. Select the Fabric Softener 

option if using liquid fabric softener to assure proper dispensing.

This washer is designed to dispense laundry boosters such as 

oxygenated stain treaters and color-safe bleach at the right time 

in the cycle for best cleaning performance. Do not use laundry 

boosters and chlorine bleach in the same cycle.

The Clean Boost with Heater option helps to ensure better soil 

and stain removal. Clean Boost uses a heater within the washer 

to maintain the selected temperature setting throughout the wash 

period. This option will add some additional time to the cycle 

based on which temperature is selected. It is a preset cycle setting 

on the Sanitary and Super Wash cycles.

Clean Boost with Heater may be selected as an option with other 

cycles. See table for details.

 

(Adds time to the wash cycle)

Default

Default

Option

Option

Option

Option