mitutoyo lsm-9506 Manual Do Utilizador
No. 99MBC032A
vi
CONTENTS
CONVENTIONS USED IN USER'S MANUAL ................................................................. i
NOTES FOR EXPORTING ...............................................................................................ii
PRECAUTIONS ...............................................................................................................iii
SAFETY PRECAUTION LABELS LOCATED ON LSM-9506 ........................................ iv
INSTALLING CONDITIONS .............................................................................................v
WARRANTY ......................................................................................................................v
NOTES FOR EXPORTING ...............................................................................................ii
PRECAUTIONS ...............................................................................................................iii
SAFETY PRECAUTION LABELS LOCATED ON LSM-9506 ........................................ iv
INSTALLING CONDITIONS .............................................................................................v
WARRANTY ......................................................................................................................v
1.
INTRODUCTION ................................................................................................... 1-1
1.1 Outline ........................................................................................................... 1-1
1.2 Foreword ....................................................................................................... 1-1
1.3 Nomenclature ................................................................................................ 1-2
1.1 Outline ........................................................................................................... 1-1
1.2 Foreword ....................................................................................................... 1-1
1.3 Nomenclature ................................................................................................ 1-2
1.3.1
Display Unit ....................................................................................... 1-2
1.3.2
Measuring Unit .................................................................................. 1-3
2.
SETUP .................................................................................................................. 2-1
2.1 Unpacking and Acceptance Check ............................................................... 2-1
2.2 Connecting the Cables ................................................................................. 2-1
2.3 Preliminary Checks ....................................................................................... 2-3
2.4 Initializing the LSM-9506 .............................................................................. 2-5
2.1 Unpacking and Acceptance Check ............................................................... 2-1
2.2 Connecting the Cables ................................................................................. 2-1
2.3 Preliminary Checks ....................................................................................... 2-3
2.4 Initializing the LSM-9506 .............................................................................. 2-5
3.
DISPLAYS AND KEY OPERATIONS .................................................................. 3-1
3.1 Outline of the Operation Modes ................................................................... 3-1
3.1 Outline of the Operation Modes ................................................................... 3-1
3.1.1
Outline of the Operation Modes ....................................................... 3-1
3.1.1.1 Overview ................................................................................. 3-1
3.1.1.2 Setting the segment ............................................................... 3-3
3.1.1.3 Measurement interval (measurement time) ........................... 3-4
3.1.1.2 Setting the segment ............................................................... 3-3
3.1.1.3 Measurement interval (measurement time) ........................... 3-4
3.1.2
Outline of the Operation Modes ....................................................... 3-5
3.1.2.1 Basic setup mode ................................................................... 3-6
3.1.2.2 Calibration mode .................................................................... 3-6
3.1.2.3 Measuring condition setup mode ........................................... 3-6
3.1.2.4 Other setup mode ................................................................... 3-6
3.1.2.5 Statistic display mode ............................................................. 3-6
3.1.2.6 Measurement mode ................................................................ 3-7
3.1.2.2 Calibration mode .................................................................... 3-6
3.1.2.3 Measuring condition setup mode ........................................... 3-6
3.1.2.4 Other setup mode ................................................................... 3-6
3.1.2.5 Statistic display mode ............................................................. 3-6
3.1.2.6 Measurement mode ................................................................ 3-7
3.2 Techniques and Terminology of Setup Functions ........................................ 3-9
3.2.1
Program ............................................................................................ 3-9
3.2.2
Basic setup ....................................................................................... 3-9
3.2.3
Function setup ................................................................................ 3-10
3.2.4
Setups according to the property of each workpiece ..................... 3-10
3.2.4.1 Transparent object (Workpiece that transmits light) ............ 3-10
3.2.5
Latch (holding) of the displayed value ........................................... 3-12
3.2.6
Automatic measurement with an edge specification ...................... 3-13
3.2.7
GO/NG judgment ............................................................................ 3-14
3.2.8
Abnormal data elimination .............................................................. 3-16
3.2.9
Offset/Zero-set ................................................................................ 3-17
3.2.10 Mastering ........................................................................................ 3-17
3.2.11 Reference value .............................................................................. 3-18
3.2.12 Data output conditions .................................................................... 3-18
3.2.13 Automatic workpiece detection <OD detection method, Position
3.2.11 Reference value .............................................................................. 3-18
3.2.12 Data output conditions .................................................................... 3-18
3.2.13 Automatic workpiece detection <OD detection method, Position
detection method> .......................................................................... 3-19