Orion steadypix 5228 Manual Do Utilizador
5
Figure 5. several different cameras attached to steadyPix. Figure 5a shows a digital camera with its
adapter in line with the camera's lens. 5b shows a digital camera that has its adapter off to one side
of the camera lens. 5c shows a 35mm film camera attached to the steadyPix.
Figure 6. the same cameras in Figure 5, but with the steadyPix attached to a telescope and ready to
shoot. note how the camera support plate must be adjusted for different camera designs.
a.
b.
c.
a.
b.
c.
You may find it handy to use a camera shutter release to take
the picture, as this will result in minimal disturbances to the
camera or telescope when snapping the photo. The move-
ment of pressing the shutter button may be enough motion to
lose the picture.
the picture, as this will result in minimal disturbances to the
camera or telescope when snapping the photo. The move-
ment of pressing the shutter button may be enough motion to
lose the picture.
4. changing the eyepiece
clamp
Some eyepieces may have barrels that are too large for the
regular eyepiece clamp to go around. For these eyepieces you
should remove the regular eyepiece clamp and replace it with
the large eyepiece clamp. You will need a crescent wrench to
change clamps.
1. Remove the shaft from the camera support plate by loos-
regular eyepiece clamp to go around. For these eyepieces you
should remove the regular eyepiece clamp and replace it with
the large eyepiece clamp. You will need a crescent wrench to
change clamps.
1. Remove the shaft from the camera support plate by loos-
ening the shaft knob and sliding the shaft out of the camera
support plate.
support plate.
2. Hold the shaft securely in one hand and use the crescent
wrench to turn the lower nut (the nut underneath the eye-
piece clamp) clockwise until it is loose. Thread the nut
clockwise a couple more turns.
piece clamp) clockwise until it is loose. Thread the nut
clockwise a couple more turns.
3. Hold the upper nut securely between your finger and thumb
so that it does not move. With your other hand, rotate the
shaft clockwise until the upper nut comes loose from the
threads of the shaft. Put the nut aside for the moment.
threads of the shaft. Put the nut aside for the moment.
4. Remove the upper washer and the clamp from the shaft,
leaving the lower nut and washer in place.
5. Put the shaft through the bottom of the large eyepiece
clamp with the SteadyPix. Then place the upper washer on
the shaft and thread the upper nut clockwise with your fin-
gers onto the threaded portion of the shaft. If there is not
enough exposed thread to hold the upper nut, remove the
washer and clamp and turn the lower nut clockwise until it
is about an 1/4" further down the threaded part of the shaft.
Then replace the clamp and washer and start threading
the upper nut onto the shaft again. Thread the upper nut as
far as you can with your fingers (it will still be loose). You
may also find it helps to hold the nut with your finger and
thumb and turn the shaft counterclockwise to thread the
upper nut.
the shaft and thread the upper nut clockwise with your fin-
gers onto the threaded portion of the shaft. If there is not
enough exposed thread to hold the upper nut, remove the
washer and clamp and turn the lower nut clockwise until it
is about an 1/4" further down the threaded part of the shaft.
Then replace the clamp and washer and start threading
the upper nut onto the shaft again. Thread the upper nut as
far as you can with your fingers (it will still be loose). You
may also find it helps to hold the nut with your finger and
thumb and turn the shaft counterclockwise to thread the
upper nut.
6. Hold the shaft securely with one hand while turning the
lower nut counter-clockwise with the crescent wrench until
it is secure against the washer and eyepiece clamp.
it is secure against the washer and eyepiece clamp.
7. Remove the eyepiece securing knob from the regular eye-
piece clamp by turning it counter-clockwise until it is
unthreaded from the top of the eyepiece clamp.
unthreaded from the top of the eyepiece clamp.