Holmes hoh2501tg Manual Do Utilizador

When using electrical appliances, basic safety precautions should 

always be followed to reduce the risk of fire, electric shock, and 

injury to persons, including the following:
1. Read all instructions before using the appliance.
2. To avoid fire or shock hazard, plug the appliance directly 

into a 120V AC electrical outlet.

3. The heater is hot when in use.  To avoid burns, DO NOT let bare

skin touch hot surfaces.  If provided, use handles when moving 

this heater.  Keep combustible materials, such as furniture, pillows,

bedding, papers, clothes, and curtains at least 3 ft (0.9 m) from the

front of the heater and keep them away from the sides and rear.

4. DO NOT run cord under carpeting.  DO NOT cover cord with throw

rugs, runners, or the like.  Arrange cord away from traffic area 

and where it will not be tripped over.

5. This heater is not intended for use in bathrooms, laundry areas 

and similar indoor location.  NEVER locate heater where it may 

fall into a bathtub or other water container.

6. Extreme caution is necessary when any heater is used by, 

or near children or invalids, and whenever the heater is left 

operating and unattended.

7. Always unplug the heater when not in use.
8. When unplugging, be sure to pull by the plug and not the cord.
9. DO NOT insert or allow foreign objects to enter any ventilation 

or exhaust opening as this may cause an electric shock or fire, 

or damage the heater.

10. DO NOT operate heater with a damaged cord or plug, or after the

heater malfunctions, has been dropped or damaged in any manner.

Return appliance to manufacturer for examination, electrical or

mechanical adjustment, or repair.

11. A heater has hot and arcing or sparking parts inside.  DO NOT 

use it in areas where gasoline, paint, or flammable liquids are 

used or stored.

12. Use appliance only for intended household use as described 

in this manual.  Any other use not recommended by the 

manufacturer may cause fire, electric shock, or injury to 

persons.  The use of attachments not recommended or sold 

by the manufacturer may cause hazards.

13. DO NOT use outdoors.
14. To prevent a possible fire, DO NOT block air intakes or exhaust 

in any manner.  DO NOT use on soft surfaces, like a bed, where

openings may become blocked. Use on floor only.

15. To disconnect heater, turn controls to OFF, then remove 

plug from outlet.

16. Avoid the use of an extension cord because the extension cord 

may overheat and cause a risk of fire.  However, if you have 

to use an extension cord, the cord shall be No. 14 AWG minimum

size and rated not less than 1875 watts.

17. DO NOT attempt to repair or adjust any electrical or mechanical

functions on this unit.  Doing so will void your warranty.  The inside

of the unit contains no user serviceable parts.  All servicing should

be performed by qualified personnel only.

1. Set the thermostat to the OFF position.
2. Plug in heater.  The power light will illuminate and remain lit 

when the heater is on.

3. For heater operation, set the Thermostat control all the way to HI.
4. Turn the Heat Setting Control to desired heat setting (LOW for 

600W, MED for 900W, or HIGH for 1500W).

During Season Care:
1. Always unplug the heater before cleaning
2. Clean the unit with a soft damp cloth.  Please be very 

cautious near the metal fins.

3. NEVER use abrasive or flammable solvents to clean the unit.
4. After cleaning, be sure to completely dry the unit with a cloth 

or towel.

After Season Care:
1. Store heater in a cool, dry location.
2. Holmes recommends that you store the unit 

in its original carton.

If your heater fails to operate:
• UNPLUG THE UNIT
• Make sure the electrical outlet or circuit breaker is working.
• The temperature may be set too low.  Turn the thermostat knob

clockwise until the heater restarts.

• Make sure selector is in LOW, MED or HIGH setting.

1. Set the Thermostat control all the way to HI.  (See fig. #2)
2. When the desired temperature/comfort level is reached, lower 

the thermostat control setting until the heater stops operating.

3. The control will now automatically maintain the pre-set temperature

level by turning the heater ON and OFF.

1. Carefully remove your heater from the box (please save 

the carton for off-season storage).

2. Make sure the unit is in the OFF position before plugging 

the heater into the outlet.

3. Place heater on firm level surface.
4. Avoid overloading your circuit by not using other high wattage 

appliances in the same outlet.  At 1500 Watts, this unit draws 

12.5 Amps

Carry Handle

Cord Wrap

Easy Roll Wheels

Carry Handle

Thermostat

OFF

I  Lo 600W
II  Med 900W
III  Hi 1500W

Power Light

MODE Control

WHEEL AND FRONT FOOT ASSEMBLY
There are two wheels, one axle, one front foot, two wing nuts, and 

one “U” bolt packed within the box that you will need to assemble 

the heater.  (Please refer to Fig. #3 & #4).
1. Insert the two wheels into the two holes in the axle.  They will snap 

in, and are not meant to be taken apart after being put into the

axle.

2. Turn the heater upside down.  You may hear a gurgling sound 

as the liquid settles.  (The control panel will be closest to the floor). 

3. Place the “U” bolt over the last joint of the heater with the 

threaded ends pointed upward.

4. Align the holes in the axle with the “U” bolt and slide into place.
5. Secure the axle with the two provided wing nuts. 
6.  While the unit is still upside down, take the front foot, and snap 

it into the corresponding holes in the front part of the heater.  

This front foot is not meant to be removed once it is attached 

to the bottom of the unit. 

Figure 3

Figure 4