ONKYO dv-sp403e Manual Do Utilizador
51
Troubleshooting
If you have any trouble using your DV-SP403E, check the following table for possible causes and remedies. If you still
can’t resolve the issue yourself, please contact your Onkyo dealer.
can’t resolve the issue yourself, please contact your Onkyo dealer.
Symptoms
Causes
Remedies
D
VD Pla
y
er
Can’t turn on the
DV-SP403E?
DV-SP403E?
The power cord is not connected.
Connect the power cord to a suitable wall outlet
(page 22).
(page 22).
External interference is affecting the
DV-SP403E’s digital circuitry.
DV-SP403E’s digital circuitry.
Turn off the DV-SP403E, wait five seconds, then
try turning it on again. If that fails, disconnect the
power cord from the wall outlet, wait five seconds,
reconnect it, then try turning it on again.
try turning it on again. If that fails, disconnect the
power cord from the wall outlet, wait five seconds,
reconnect it, then try turning it on again.
The disc tray won’t
close properly?
close properly?
The disc is not centered in the disc tray.
Place the disc in the center of the disc tray
(page 25).
(page 25).
The disc is dirty.
Can’t start playback?
No disc is loaded.
The disc cannot be played because it’s
incompatible.
incompatible.
The disc is upside down.
Load the disc the correct way up (page 25).
The disc is not centered in the disc tray.
Place the disc in the center of the disc tray
(page 25).
(page 25).
The disc is dirty.
The disc uses parental lock and the Paren-
tal Lock function is on.
tal Lock function is on.
Turn off the Parental Lock function (page 43).
The DVD-Video disc is intended for use
in another region.
in another region.
If the region number on the disc does not match
the region number on the DV-SP403E, the disc
can’t be played (page 47).
the region number on the DV-SP403E, the disc
can’t be played (page 47).
The picture distorts
occasionally?
occasionally?
The disc is dirty.
You’re using the Fast Forward or Fast
Reverse function.
Reverse function.
A little picture distortion may occur when using
these functions. This is normal.
these functions. This is normal.
Picture instability or
noise?
noise?
The DV-SP403E is connected to your TV
via a VCR or other video equipment and a
copy-protection system is affecting the
picture.
via a VCR or other video equipment and a
copy-protection system is affecting the
picture.
Connect the DV-SP403E directly to your TV
(page 18).
(page 18).
No picture?
The wrong input source is selected on
your TV.
your TV.
On your TV, select the input to which the
DV-SP403E is connected.
DV-SP403E is connected.
The video cable is not connected properly.
Check the video cable and correct as necessary
(page 18).
(page 18).
Settings are not saved?
If there’s a power failure, or the power
cord is disconnected inadvertently, any
settings are lost.
cord is disconnected inadvertently, any
settings are lost.
Before you disconnect the power cord, set the
DV-SP403E to Standby by pressing the
[STANDBY/ON] button, and wait until “OFF”
has disappeared from the display.
DV-SP403E to Standby by pressing the
[STANDBY/ON] button, and wait until “OFF”
has disappeared from the display.
Brightness is unstable
or the picture is noisy?
or the picture is noisy?
The DV-SP403E is connected to your TV
via a VCR or other video equipment and a
copy-protection system is affecting the
picture.
via a VCR or other video equipment and a
copy-protection system is affecting the
picture.
Connect the DV-SP403E directly to your TV
(page 18).
(page 18).
Your TV doesn’t support progressive
scanning.
scanning.
Reset the DV-SP403E to its initial settings
(page 40).
(page 40).
Chapters or tracks don’t
play in the correct
order?
play in the correct
order?
You are using repeat playback, program
playback, or random playback.
playback, or random playback.
Buttons on the
DV-SP403E and remote
controller don’t work?
DV-SP403E and remote
controller don’t work?
Power supply voltage fluctuations and
other anomalies, such as static electricity,
can interfere with normal operation.
other anomalies, such as static electricity,
can interfere with normal operation.
Turn off the DV-SP403E, wait five seconds, then
turn it on again. If that doesn’t resolve the issue,
disconnect the power cord from the wall outlet,
wait five seconds, reconnect it, then try again.
turn it on again. If that doesn’t resolve the issue,
disconnect the power cord from the wall outlet,
wait five seconds, reconnect it, then try again.