ONKYO dps-5.5 Manual Do Utilizador
23
Connecting the Power/Turning on the DPS-5.5
Before connecting
• The DPS-5.5 is shipped with the Power switch in the
on position (
On). When the power cord is plugged
in for the first time, the DPS-5.5 will automatically
enter the standby state and the Standby indicator will
light (same condition after step 2 below).
enter the standby state and the Standby indicator will
light (same condition after step 2 below).
• Make sure that all the connections on pages 18 – 22
are complete (the connection to a TV is required).
Note:
• This player features a screen saver and an auto power
off function. If the player is stopped and no button is
pressed for five minutes, the screen saver starts. If the
disc tray is closed but no disc is playing and no control
is pressed for 30 minutes, the player automatically
goes into standby.
pressed for five minutes, the screen saver starts. If the
disc tray is closed but no disc is playing and no control
is pressed for 30 minutes, the player automatically
goes into standby.
1
Plug the supplied power cord
into the AC INLET and then into
the power outlet on the wall.
into the AC INLET and then into
the power outlet on the wall.
• Do not use a power cord other than
the one supplied with the DPS-5.5.
The power cord supplied is designed
for use with the DPS-5.5 and should
not be used with any other device.
The power cord supplied is designed
for use with the DPS-5.5 and should
not be used with any other device.
• Never have the power cord discon-
nected from the DPS-5.5 while the
other end is plugged into the wall
outlet. Doing so may cause an elec-
tric shock. Always connect by plug-
ging into the wall outlet last and
disconnect by unplugging from the
wall outlet first.
other end is plugged into the wall
outlet. Doing so may cause an elec-
tric shock. Always connect by plug-
ging into the wall outlet last and
disconnect by unplugging from the
wall outlet first.
2
Press Power to switch on the
main power.
main power.
The DVD Player enters standby mode.
The Standby indicator lights up.
• The buttons on the remote controller
The Standby indicator lights up.
• The buttons on the remote controller
do not operate if the Power switch is
set to Off.
set to Off.
• To switch off the main power, press
Power again.
DPS-5.5
Standby/On
O f f
Power
Play Mode
Clear
Display
Dimmer
Play
Stop
Pause
Open /Close
Standby
On
Standby/On
Power
To a wall outlet
On
O f f
Power
3
Press Standby/On on the DVD
Player or On on the remote con-
troller.
Player or On on the remote con-
troller.
The DVD Player turns on and the
Standby indicator turns off.
• To put the DVD Player in the standby
Standby indicator turns off.
• To put the DVD Player in the standby
mode, press Standby/On on the DVD
Player, or Standby on the remote
controller. Be sure to set the volume
to minimum before putting the DVD
Player in the standby mode for the
next use to avoid sudden loud sound
reproduction.
Player, or Standby on the remote
controller. Be sure to set the volume
to minimum before putting the DVD
Player in the standby mode for the
next use to avoid sudden loud sound
reproduction.
• While the Standby indicator lights
up, the DVD Player can receive sig-
nals from the remote controller.
However, if you press Power on the
DVD Player to switch off the main
power, the remote controller cannot
be used to turn on the DVD Player.
nals from the remote controller.
However, if you press Power on the
DVD Player to switch off the main
power, the remote controller cannot
be used to turn on the DVD Player.
• Setting the Standby button to standby
does not shut off the power com-
pletely.
pletely.
Standby/On
DPS-5.5_En.book Page 23 Monday, May 17, 2004 4:45 PM