Intex Recreation 634 Manual Do Utilizador
110
SAVE THESE INSTRUCTIONS
Page 7
(110) MODEL 634 FILTER PUMP ENGLISH 7.5” X 10.5” PANTONE 295U 01/31/2007
SS
EE
TT
--UU
PP
II
NN
SS
TT
RR
UU
CC
TT
IIOO
NN
SS
1. Grasp the strainer and plunger valve
mechanism.
2. In a counter-clockwise motion unscrew
plunger valve union from the threaded
strainer connector (14). Be careful not
to lose the step rubber washer (11).
Place the plunger valve on the ground
in a safe place (see drawing 1).
strainer connector (14). Be careful not
to lose the step rubber washer (11).
Place the plunger valve on the ground
in a safe place (see drawing 1).
3. In a counter-clockwise motion unscrew
the strainer nut (12) from the threaded
connector (14). Leave the flat
washer (13) on the connector (14).
connector (14). Leave the flat
washer (13) on the connector (14).
4. From the inside of the pool liner insert
the connector (14) into one of the
pre-cut holes with the washer remaining
on the connector to be placed against
the inside of the liner wall.
pre-cut holes with the washer remaining
on the connector to be placed against
the inside of the liner wall.
5. With the flat side of the strainer nut (12)
facing the outside wall of the liner in a
clockwise motion screw the strainer
nut (12) back onto the threaded
connector (14) (see drawing 2). Before
assembly, lubricate the threads with a
petroleum jelly.
clockwise motion screw the strainer
nut (12) back onto the threaded
connector (14) (see drawing 2). Before
assembly, lubricate the threads with a
petroleum jelly.
6. Finger tighten the strainer grid (15) and
the strainer nut (12) onto the threaded
connector (14).
connector (14).
7. Grasp the plunger valve assembly. Make
sure the step washer (11) is in place.
8. In a clockwise motion screw the plunger
valve union back onto the threaded
connector (14) (see drawing 3).
connector (14) (see drawing 3).
9. Examine the plunger valve to see if the
handle is pushed fully down to the "0/1"
position. If not, then grasp the handle at
the top and push down turning the
handle in a clockwise direction until the
plastic protruding notch anchors in
the "0/1" position. This will prevent
water from flowing out during filling
(see drawings 4.1 & 4.2).
position. If not, then grasp the handle at
the top and push down turning the
handle in a clockwise direction until the
plastic protruding notch anchors in
the "0/1" position. This will prevent
water from flowing out during filling
(see drawings 4.1 & 4.2).
10. Repeat steps 1 through 9 for the 2nd
liner pre-cut hole.
11. The pool liner is now ready to fill with
water. Consult the above-ground-pool
owner’s manual for filling instructions.
owner’s manual for filling instructions.
STRAINER & PLUNGER VALVE SET-UP
1
The Krystal Clear™ filter pump assembly includes two strainer-control
mechanisms that are to be installed in the pool liner’s two pre-cut holes. The
strainer grid prevents large objects from jamming and/or damaging the filter
pump and the plunger valve assembly prevents water from flowing into the
filter pump while the filter cartridge is being placed or cleaned. For Easy
Set™ Pools, install the strainer and plunger valve before inflating the pool
liner top ring.
mechanisms that are to be installed in the pool liner’s two pre-cut holes. The
strainer grid prevents large objects from jamming and/or damaging the filter
pump and the plunger valve assembly prevents water from flowing into the
filter pump while the filter cartridge is being placed or cleaned. For Easy
Set™ Pools, install the strainer and plunger valve before inflating the pool
liner top ring.
2
3
4.1
4.2
13
14
15
INSIDE
LINER WALL
INSIDE
LINER
WALL
12
2
1
2
2
1
1