Morphy Richards ib29104 Manual Do Utilizador
Connect the speakers to main unit
1 Ensure the mains power is disconnected.
2 Connect the speaker wires between the main unit and the speakers.
Match the speaker wire to the appropriate terminal on the components:
(+) to (+) (colour), and (-) to (-) (black). (If the wires are reversed, the
sound will be distorted and will lack some tones.)
(+) to (+) (colour), and (-) to (-) (black). (If the wires are reversed, the
sound will be distorted and will lack some tones.)
3 Hold down the terminal tab to insert each wire. Release the tab to lock
the wire into the terminal. Make sure the bare wire is fully inserted and
that the insulation reaches right up to the tab
leaving no bare wire visible.
that the insulation reaches right up to the tab
leaving no bare wire visible.
•
To avoid short-circuiting the speakers, make
sure the the stripped end of each speaker
wire does not touch another terminal or
another wire.
sure the the stripped end of each speaker
wire does not touch another terminal or
another wire.
Connect the aerials
Plug the RF coax plug of the FM aerial lead into the external FM antenna
socket.
socket.
Assemble the MW loop aerial by bending the
stand along the join and continue to bend until
the stand is at the bottom of the aerial. Clip into
the slot in the base of the aerial. Then connect
the two wires from the MW aerial to the external
MW antenna terminals (in the same way the
speakers wires are connected).
stand along the join and continue to bend until
the stand is at the bottom of the aerial. Clip into
the slot in the base of the aerial. Then connect
the two wires from the MW aerial to the external
MW antenna terminals (in the same way the
speakers wires are connected).
Put a battery in the remote
control
control
Pull out the battery tray and put in a CR2025
battery. Please observe correct polarity.
battery. Please observe correct polarity.
If the unit is not to be used for a prolonged
period, remove batteries to avoid battery
leakage. In the interests of environmental safety,
dispose of batteries safely.
period, remove batteries to avoid battery
leakage. In the interests of environmental safety,
dispose of batteries safely.
Connect to the wall socket
Plug the unit into a live wall outlet.
Backlight illumination in standby mode
Press any key (except
ON/STANDBY
) on the control panel or the remote
control (when unit in standby mode) and the backlight for the display
illuminates and remains on for 10-seconds for you to check the
information on the display.
illuminates and remains on for 10-seconds for you to check the
information on the display.
Digital clock & timer settings
How to set correct time (in standby mode)
1 Press and hold
CLK.ADJ
for more than 2 seconds.
2 Press
SKIP/SEARCH
to adjust the hours, press
CLK.ADJ
again to set
minutes.
3 Press
CLK.ADJ
to skip to timer setting mode.
4 The time set will remain until you switch off the unit by the power
switch.
To set the time by the remote control, enter the hour and minutes using
the numeric buttons.
the numeric buttons.
Alarm clock/timer function
How to preset the timer function (during operation)
With the unit working, press and hold
CLK.ADJ
to toggle between the
following modes:
Timer on
Timer on hour
Timer on minute
Timer on mode
(power on with CD playback or tuned in radio station)
Timer on
volume
Timer off
Timer off hour
Timer off minute.
Adjust the timer on/off hour & minute by means of
SKIP/SEARCH
buttons.
Choose timer on mode between CD/Tuner by means of
SKIP/SEARCH
buttons.
To turn off alarm hold down sleep/alarm on remote control.
Sleep function
1 Press
SLEEP/ALARM
on the remote control during CD playback or radio
broadcasting.
2 Then press
SLEEP/ALARM
to change display and sleep time in a
sequence: 90
80
70
60
50
40
30
20
10
off.
When the sleep function is activated, the unit goes into standby mode the
3