Kenwood TS-590S Manual Do Utilizador
27
(1+$1&('&20081,&$7,216
•
Press [SCAN (SG.SEL)] or [CLR] to stop
scanning while the CTCSS frequency ID scan is
active.
scanning while the CTCSS frequency ID scan is
active.
•
Press [SCAN (SG.SEL)] again to resume
scanning.
scanning.
Note: Received signals are audible while scanning is in
progress.
progress.
&5266721(
Use this feature when using different uplink and
downlink tones to access a repeater. You can set a
transmission Tone frequency and reception CTCSS
frequency to different frequencies.
downlink tones to access a repeater. You can set a
transmission Tone frequency and reception CTCSS
frequency to different frequencies.
To set the transmission tone:
1 Press [A/B (A=B)] to select VFO A or VFO B.
2 Select your desired transmission frequency.
3 Press [FM/AM (FM-N)] to select FM.
4 Press [AGC/T (SEL)] until “ ” appears.
5 Press and hold [AGC/T (SEL)], then rotate the
MULTI/CH control to select your desired Tone
frequency.
frequency.
6 Press and hold [AGC/T (SEL)] or press [CLR] to
complete the setting.
To set the reception tone:
1 Press [A/B (A=B)] to select the other VFO.
2 Select your desired reception frequency.
3 Press [FM/AM (FM-N)] to select FM.
4 Press [AGC/T (SEL)] until “
” appears.
5 Press and hold [AGC/T (SEL)], then rotate the
MULTI/CH control to select your desired CTCSS
frequency.
frequency.
6 Press and hold [AGC/T (SEL)] or press [CLR] to
complete the setting.
To set the Cross tone:
1 Press [SPLIT].
•
“SPLIT” appears on the display.
2 Press [AGC/T (SEL)] until “
” appears.
Note: hen the cross tone function is ON, the Tone and CTCSS
frequency cannot be changed. To change the Tone or CTCSS
frequency, press [AGC/T (SEL)] to turn Tone or CTCSS ON,
then change the setting.
frequency cannot be changed. To change the Tone or CTCSS
frequency, press [AGC/T (SEL)] to turn Tone or CTCSS ON,
then change the setting.
8 Turn the MULTI/CH control to select the
appropriate CTCSS frequency.
•
The selectable CTCSS frequencies are listed in
the table below.
the table below.
9 Press and hold [AGC/T (SEL)] or press [CLR] to
complete the setting.
No.
Freq.
(Hz)
No.
Freq.
(Hz)
No.
Freq.
(Hz)
No.
Freq.
(Hz)
00
67.0
11
97.4
22
141.3
33
206.5
01
69.3
12
100.0
23
146.2
34
210.7
02
71.9
13
103.5
24
151.4
35
218.1
03
74.4
14
107.2
25
156.7
36
225.7
04
77.0
15
110.9
26
162.2
37
229.1
05
79.7
16
114.8
27
167.9
38
233.6
06
82.5
17
118.8
28
173.8
39
241.8
07
85.4
18
123.0
29
179.9
40
250.3
08
88.5
19
127.3
30
186.2
41
254.1
09
91.5
20
131.8
31
192.8
--
--
10
94.8
21
136.5
32
203.5
--
--
You will hear calls only when the selected tone is
received. To answer the call, press and hold Mic
[PTT], then speak into the microphone.
received. To answer the call, press and hold Mic
[PTT], then speak into the microphone.
Skip steps 7 and 8 if you have already programmed
the appropriate CTCSS frequency.
the appropriate CTCSS frequency.
Note:
X
When using split-frequency operation, select FM mode on
both VFOs to use CTCSS.
both VFOs to use CTCSS.
X
You can select a CTCSS frequency independent of a tone
frequency.
frequency.
X
You cannot use the CTCSS function with the Tone function.
&7&66)5(48(1&<,'6&$1
This function scans through all CTCSS frequencies to
identify the incoming CTCSS frequency on a received
signal. You may find this useful when you cannot
recall the CTCSS frequency that the other persons in
your group are using.
identify the incoming CTCSS frequency on a received
signal. You may find this useful when you cannot
recall the CTCSS frequency that the other persons in
your group are using.
1 While the CTCSS function is ON, press and hold
[AGC/T (SEL)].
•
The current CTCSS frequency appears.
2 Press [SCAN (SG.SEL)] to activate the CTCSS
frequency ID scan.
•
While the transceiver is receiving a signal, “
”
blinks and every CTCSS frequency is scanned.
When the CTCSS frequency is identified, the
transceiver stops scanning and the identified
frequency is displayed.
When the CTCSS frequency is identified, the
transceiver stops scanning and the identified
frequency is displayed.