Vulcan Materials vc44gd Manual Do Utilizador
– 6 –
ASSEMBLING STACKED OVENS
Unpack the ovens and stack kit. Position the oven to be used as
the bottom oven on its back for access to the oven bottom, taking
care not to scratch or damage it. The gas pipe protrudes beyond the
back; provide for this when the oven is tipped back by resting it on
suitable spacers (2 x 4" [51 x 102 mm], etc.). Attach the four leg
assemblies with the 24 bolts and lockwashers (six per leg).
the bottom oven on its back for access to the oven bottom, taking
care not to scratch or damage it. The gas pipe protrudes beyond the
back; provide for this when the oven is tipped back by resting it on
suitable spacers (2 x 4" [51 x 102 mm], etc.). Attach the four leg
assemblies with the 24 bolts and lockwashers (six per leg).
Place the lower oven (with legs) on the floor and remove two
7
/
16
inch
(11 mm) diameter knockouts on each side of the top cover. Remove
vent guard and discard it.
vent guard and discard it.
Move the oven with legs to the installed position and place upper
oven on top of lower oven using the locating studs.
oven on top of lower oven using the locating studs.
Install the stacking flue (Fig. 3) with the four screws provided.
Connect the piping between the top oven and bottom oven. For all
gas supply connections, pipe joint compound must be resistant to
the action of propane gases.
gas supply connections, pipe joint compound must be resistant to
the action of propane gases.
LEVELING
Make sure that the oven racks are level in the final installed position. If the oven is installed on legs,
turn the adjustable feet in or out to level the oven front-to-back and side-to-side. If the oven is installed
on casters, loosen set screws and turn casters in or out to level the oven front-to-back and side-to-side.
Retighten set screws after leveling.
turn the adjustable feet in or out to level the oven front-to-back and side-to-side. If the oven is installed
on casters, loosen set screws and turn casters in or out to level the oven front-to-back and side-to-side.
Retighten set screws after leveling.
Assembling the Legs to the Oven
The legs must be installed on the bottom of the oven. Gently position the
oven on its side, taking care not to scratch or damage it.
oven on its side, taking care not to scratch or damage it.
Attach each of the four leg assemblies to the bottom of the oven with the
24 bolts and lockwashers (six per leg). Carefully raise the oven to its
normal position.
24 bolts and lockwashers (six per leg). Carefully raise the oven to its
normal position.
ASSEMBLING THE STAND TO THE OVEN
Attach each of the four leg assemblies to the bottom of the oven with the
24 bolts and lockwashers (six per leg). Carefully raise the oven to its
normal position.
24 bolts and lockwashers (six per leg). Carefully raise the oven to its
normal position.
Attach the undershelf to the legs with eight bolts and lockwashers
(two per leg).
(two per leg).
Install the rack guides into the undershelf at desired locations (for pan
or flat rack), then attach the rack supports to the top end of the rack
guides. Attach rack supports to the leg assembly by removing one
middle bolt and reattaching back through the end holes in the rack
support (Fig. 2).
or flat rack), then attach the rack supports to the top end of the rack
guides. Attach rack supports to the leg assembly by removing one
middle bolt and reattaching back through the end holes in the rack
support (Fig. 2).
Fig. 2
Fig. 3
STACKING FLUE
PL-53564
BACK
FRONT
RACK SUPPORT
RACK GUIDE
PL-56178