Bay Technical Associates BayTech DS72 Manual Do Utilizador
DS72 Host Module
6
from a DB-25 connector to an RJ-45 connector is also available from Bay Tech, upon request (Bay
Tech Part No. 25FRJ45PC-4). The 8-pin crossed modular cable is configured for these adapters.
Tech Part No. 25FRJ45PC-4). The 8-pin crossed modular cable is configured for these adapters.
NOTE: Use rollover (RJ08X007) RJ-45 cables when using modular connectors to interface the
DS-Series to another BayTech product with modular connectors, such as the RPC Remote
Power Control Unit.
DS-Series to another BayTech product with modular connectors, such as the RPC Remote
Power Control Unit.
10/100 BASE-T NETWORK PORT CONNECTION
Using a straight 10/100 Base-T cable, connect the RJ-45 port labeled ETHERNET on the HOST
module to an RJ-45 port on the network hub. The LINK (link integrity) LED, located on the front
panel of the HOST, illuminates when a good connection is established between the HOST and the hub.
module to an RJ-45 port on the network hub. The LINK (link integrity) LED, located on the front
panel of the HOST, illuminates when a good connection is established between the HOST and the hub.
EXTERNAL MODEM CONNECTION
Using the 25MRJ45MD-6 adapter (or other applicable adapter) and the RJ08X007 crossed cable,
connect the COM (or serial) port of the modem to the RJ-45 port labeled EIA-232 on the DS62-MD4
module. Using an RJ04X007 (RJ-11) modular cable, connect the port labeled “LINE” on the modem to
the Telco wall jack. Using communications software package, dial the modem. Setup Instruction at
end of manual.
connect the COM (or serial) port of the modem to the RJ-45 port labeled EIA-232 on the DS62-MD4
module. Using an RJ04X007 (RJ-11) modular cable, connect the port labeled “LINE” on the modem to
the Telco wall jack. Using communications software package, dial the modem. Setup Instruction at
end of manual.
Installation
UNPACKING
Compare the unit and serial number of the equipment you received to the packing slip located on the
outside of the box. Inspect equipment carefully for damage that may have occurred in shipment. If
there is damage to the equipment or if materials are missing, contact BayTech technical support at 228-
563-7334 or call toll free inside the United States at 800-523-2702. At a minimum, you should receive
the following:
Compare the unit and serial number of the equipment you received to the packing slip located on the
outside of the box. Inspect equipment carefully for damage that may have occurred in shipment. If
there is damage to the equipment or if materials are missing, contact BayTech technical support at 228-
563-7334 or call toll free inside the United States at 800-523-2702. At a minimum, you should receive
the following:
1. The DS72 Module.
2. Manual insert describing the location of the User’s Guide on BayTech’s website at
2. Manual insert describing the location of the User’s Guide on BayTech’s website at
www.baytech.net
.
3. Power Cords that may be attached to the unit (if order requested detachable cords).
4. 1 ea. DE-9 (9 pin) PC com port adapter -- 9FRJ45PC (with Cisco Interface) or 9FRJ45PC-1.
5. 1 ea. RJ-45 Roll over cable -- RJ08X007.
4. 1 ea. DE-9 (9 pin) PC com port adapter -- 9FRJ45PC (with Cisco Interface) or 9FRJ45PC-1.
5. 1 ea. RJ-45 Roll over cable -- RJ08X007.
NOTE: Keep shipping container and packing material in the event future shipment is
required.
required.
PREPARING THE INSTALLATION
The installation area should be clean and free of extreme temperatures and humidity. Allow sufficient
space behind the DS unit for cabling and receptacle connections. Access to installation site should be
restricted to authorized personnel. Installation of these units should be limited to ITE and Telco server
environments.
space behind the DS unit for cabling and receptacle connections. Access to installation site should be
restricted to authorized personnel. Installation of these units should be limited to ITE and Telco server
environments.
Power
CAUTION: This unit is intended for indoor use only in a clean and free of extreme temperatures and
humidity. Do not install near water or expose this unit to moisture. To prevent heat buildup, do not coil
the power cord when in use. Do not use extension cords. Do not attempt to make any internal changes
humidity. Do not install near water or expose this unit to moisture. To prevent heat buildup, do not coil
the power cord when in use. Do not use extension cords. Do not attempt to make any internal changes