Kenwood KDC-U4549 Manual Do Utilizador
English
35
Symptom
Remedy/Cause
Correct characters are not displayed
(e.g. album name).
(e.g. album name).
This unit can only display letters (upper case), numbers, and a limited number of symbols.
Bluetooth
Symptom
Remedy/Cause
The hands-free talk volume is low. The hands-free talk volume can be adjusted independently. Adjust it during hands-free talk.
[MIC GAIN], [NR LEVEL] and [EC LEVEL] of <Bluetooth Setup> (page 25).
No beep is heard at reception of
an incoming call.
an incoming call.
No beep is heard depending on the type of your cell-phone. The [CALL BEEP] of <Bluetooth
Setup> (page 25) is set ON.
Setup> (page 25) is set ON.
Voice is not recognized.
■
The vehicle window is open. If the surrounding noise is large, voice cannot be recognized
properly. Close the vehicle windows to reduce noise.
properly. Close the vehicle windows to reduce noise.
■
Small voice. If voice is too small, it cannot be recognized properly. Speak into the microphone a
little more loudly and naturally.
little more loudly and naturally.
■
The person uttering the voice tag is not the one who registered the it. Only the voice of the
person who registered the voice tag can be recognized.
person who registered the voice tag can be recognized.
“NO NUMBER” appears.
The calling party does not notify a caller ID. / There is no phone number data.
“NO DATA” appears.
There is no outgoing call list. / There is no incoming call list. / There is no missed call list. / There
is no phone book list.
is no phone book list.
“NO ENTRY” appears.
The cell-phone has not been registered (pairing).
“HF DISCONCT” appears.
The unit cannot communicate with the cell-phone.
“HF ERROR 07” appears.
The memory cannot be accessed. Turn off the power and on again. If this message still appears,
press the reset button on the control unit.
press the reset button on the control unit.
“HF ERROR 68” appears.
The unit cannot communicate with the cell-phone. Turn off the power and on again. If this
message still appears, press the reset button on the control unit.
message still appears, press the reset button on the control unit.
“UNKNOWN” appears.
The Bluetooth device cannot be detected.
“DEVICE FULL” appears.
5 Bluetooth device have already been registered. No more Bluetooth device cannot be registered.
“PIN CODE NG” appears.
The PIN code is wrong.
“CONNECT NG” appears.
The unit cannot be connected to the device.
“PAIRING NG” appears.
Pairing error.
“NO MARCHING” appears.
The voice tag is wrong. Voice cannot be recognized because of an unregistered voice tag, etc.
“TOO SOFT” appears.
Voice is too small and cannot be recognized.
“TOO LOUD” appears.
Voice is too large to be recognized.
“TOO LONG” appears.
The word or utterance is too long to be recognized.
“NO PHONEBOOK” appears.
Data is not contained in the phone book.
“NO MESSAGE” appears.
No short message in In Box.
“NO RECORD” appears.
The voice tag is not registered in the phone book.
“MEMORY FULL” appears.
The number of voice tags reaches the maximum number to be registered in the phone book.
“NO VOICE” appears.
No call.
The sound from the Bluetooth
audio player is discontinuous.
audio player is discontinuous.
■
Another Bluetooth device is affecting the Bluetooth communication. Turn off another
Bluetooth device. Move another Bluetooth device away from this unit.
Bluetooth device. Move another Bluetooth device away from this unit.
■
Another Bluetooth device or profile is used for communication. The downloading of the Phone
book or the SMS disconnects the sound.
book or the SMS disconnects the sound.
B64-4803-10_01_M_English.indd 35
B64-4803-10_01_M_English.indd 35
11/01/06 15:11
11/01/06 15:11