Fujitsu J2X1-7611-03ENZ0 Manual Do Utilizador
3.
Power OFF
Shut down the server to replace if it is still powered on.
For details on shutting down servers, refer to "Chapter 14 Power Control" in the "User's Guide VE".
For details on shutting down servers, refer to "Chapter 14 Power Control" in the "User's Guide VE".
4.
Replace the Server
Replace the server.
Use the Maintenance Wizard of the Management Board Web-UI to perform replacement.
For details on the Maintenance Wizard, refer to the PRIMEQUEST manual.
Also, change the BIOS settings of the replacement server to match the operating environment.
For details on BIOS settings, refer to "8.2 Configure the Server Environment" in the "Design Guide CE".
Shut down the server after completing BIOS settings.
Use the Maintenance Wizard of the Management Board Web-UI to perform replacement.
For details on the Maintenance Wizard, refer to the PRIMEQUEST manual.
Also, change the BIOS settings of the replacement server to match the operating environment.
For details on BIOS settings, refer to "8.2 Configure the Server Environment" in the "Design Guide CE".
Shut down the server after completing BIOS settings.
5.
Re-configure Hardware Properties after Replacement
After replacing the server, re-configure Resource Orchestrator with the latest hardware properties.
For details on how to re-configure hardware properties, refer to "
For details on how to re-configure hardware properties, refer to "
6.
Restore the Boot Disk
-
Local Boot
There is no need to restore the boot disk if the original disk is installed on the replaced server. Simply power on the
replacement server.
If the boot disk was replaced and a system image backup was collected, restore that backup.
Refer to "16.3 Restoring a System Image" in the "User's Guide VE" for details on how to restore a system image. After the
system image is restored, the server will be automatically powered on.
If there is no backup of the system image, run the installation program again.
replacement server.
If the boot disk was replaced and a system image backup was collected, restore that backup.
Refer to "16.3 Restoring a System Image" in the "User's Guide VE" for details on how to restore a system image. After the
system image is restored, the server will be automatically powered on.
If there is no backup of the system image, run the installation program again.
-
SAN Boot
As the replaced server can be easily configured to access the original boot disk using HBA address rename there is no need
to restore the boot disk. Simply power on the replacement server.
to restore the boot disk. Simply power on the replacement server.
7.
Release Maintenance Mode
Release the replaced server from maintenance mode.
For details on maintenance mode, refer to "Appendix C Maintenance Mode" in the "User's Guide for Infrastructure
Administrators (Resource Management) CE".
For details on maintenance mode, refer to "Appendix C Maintenance Mode" in the "User's Guide for Infrastructure
Administrators (Resource Management) CE".
-
Servers with no Agent Registered
Use the following procedure to replace servers on which no Resource Orchestrator agent was registered.
1.
Power OFF
Shut down the server to replace if it is still powered on.
For details on shutting down servers, refer to "Chapter 14 Power Control" in the "User's Guide VE".
For details on shutting down servers, refer to "Chapter 14 Power Control" in the "User's Guide VE".
2.
Replace the Server
Replace the server.
Use the Maintenance Wizard of the Management Board Web-UI to perform replacement.
For details on the Maintenance Wizard, refer to the PRIMEQUEST manual.
Also, change the BIOS settings of the replacement server to match the operating environment.
For details on BIOS settings, refer to "8.2 Configure the Server Environment" in the "Design Guide CE".
Shut down the server after completing BIOS settings.
Use the Maintenance Wizard of the Management Board Web-UI to perform replacement.
For details on the Maintenance Wizard, refer to the PRIMEQUEST manual.
Also, change the BIOS settings of the replacement server to match the operating environment.
For details on BIOS settings, refer to "8.2 Configure the Server Environment" in the "Design Guide CE".
Shut down the server after completing BIOS settings.
3.
Re-configure Hardware Properties after Replacement
After replacing the server, re-configure Resource Orchestrator with the latest hardware properties.
For details on how to re-configure hardware properties, refer to "
For details on how to re-configure hardware properties, refer to "
9.3.3 Replacing and Adding Server Components
This section explains how to replace and add server components.
- 58 -