fisher--paykel gwl15 ins Manual Do Utilizador
DRAIN HOSE
The drain hose guide MUST be
fitted to the drain hose and should
not extend more than 3/4” (20mm)
from the end of the guide. Place
the drain hose in tub or standpipe.
fitted to the drain hose and should
not extend more than 3/4” (20mm)
from the end of the guide. Place
the drain hose in tub or standpipe.
INLET HOSE
CONNECTIONS
LEVELING
Make sure washer is level and
four rubber inserts are properly
installed.
four rubber inserts are properly
installed.
OPERATION
1.Turn faucets on. Check for leaks,
noise, vibration, correct water
temperatures and proper
operation in spin.
2.Turn hot and cold water faucets off
and instruct customer to do the
same when washer is not in use.
same when washer is not in use.
3. Give customer the Use & Care
Book and Installation Instructions.
GROUNDING
MUST be properly grounded to
conform to local codes and
ordinances.
conform to local codes and
ordinances.
WARNING: Improper connection of
equipment-grounding conductor can
result in a risk of electric shock. Check
with a qualified electrician or
serviceman if you are in doubt as to
whether the appliance is properly
grounded.
equipment-grounding conductor can
result in a risk of electric shock. Check
with a qualified electrician or
serviceman if you are in doubt as to
whether the appliance is properly
grounded.
FINAL CHECK LIST
HAVE YOU CARRIED OUT THE FOLLOWING
NOTE TO THE INSTALLER
After you have followed the procedures on
the previous pages. Check the following.
PULL HOSE
THROUGH
GUIDE
READ AND OBSERVE ALL SAFETY INSTRUCTIONS - CONSULT
THE PRODUCT USE & CARE BOOK FOR CUSTOMER CAUTIONS
Filter end must
be connected
to faucet.
be connected
to faucet.
Faucet
end of
hose
end of
hose
3/4”
(20mm)
Specification subject to change without notice
P/N 420264A
INSTALLATION INSTRUCTIONS FOR YOUR
ECO SMART WASHER
BEFORE YOU BEGIN - READ THESE INSTRUCTIONS COMPLETELY AND CAREFULLY.
IMPORTANT - OBSERVE ALL GOVERNING CODES AND ORDINANCES.
Note to installer:
Be sure to leave these instructions with the Customer.
Note to Consumer:
Keep these instructions with your Use & Care Book for future reference.
Note:
This appliance must be properly grounded.
INSTALLATION REQUIREMENTS
LOCATION
Washer must be installed on firm
flooring to minimize vibration during
spin cycles. Concrete flooring is
best, but wood base is sufficient
providing floor support meets FHA
standards.
flooring to minimize vibration during
spin cycles. Concrete flooring is
best, but wood base is sufficient
providing floor support meets FHA
standards.
Washer should not be installed on
rugs or exposed to the weather.
rugs or exposed to the weather.
PLUMBING
Water Temperature
Water Temperature
Your cold water should not exceed
95˚F (35˚C) or your hot water exceed
150˚F (65˚C). Temperatures above
this may damage your washer.
95˚F (35˚C) or your hot water exceed
150˚F (65˚C). Temperatures above
this may damage your washer.
Shut off valves
Both hot and cold shut-off valves
(faucets) should be available in
laundry area.
(faucets) should be available in
laundry area.
Drain
Water may be drained into a
standpipe or set tub. The standpipe
must be 1
standpipe or set tub. The standpipe
must be 1
1
/
2
” (38mm) minimum
inside diameter and must be open to
the atmosphere.
the atmosphere.
ELECTRICAL
This appliance must be supplied with
110V-120V, 60Hz, and connected
to an individual, properly grounded
branch circuit, protected by a 15 or
20 amp circuit breaker or time
delay fuse.
110V-120V, 60Hz, and connected
to an individual, properly grounded
branch circuit, protected by a 15 or
20 amp circuit breaker or time
delay fuse.
Specification subject to change without notice
SPECIFICATIONS
Inlet water pressure
Max 150 psi (1MPa)
Min 3 psi (20kPa )
Standpipe Height
33
1/2
” to 78”
HEIGHT
Lid Clearance
Allow for
adjustable
feet
adjustable
feet
DEPTH
WIDTH
MODEL
All models
DEPTH
25
1/2
” (650mm)
WIDTH
25
1/2
” (650mm)
HEIGHT to top of console 40
1/2
”- 41
1/2
” (1020-1050mm)
HEIGHT LID OPEN
55
1/2
”- 56
1/2
” (1410-1440mm)
DIMENSIONS
Washer
end of
hose
end of
hose
Faucet
end of
hose
end of
hose
REMOVE TRANSIT
BOTTOM PACKER
Bottom packer MUST be removed
from the base of the washer, before
the basket packer is removed.
from the base of the washer, before
the basket packer is removed.
Washer
end of
hose.
end of
hose.