Jacuzzi led series j-230 Manual Do Utilizador
page 22
10.4 Selecting Desired Massage Action (J-210 & J-220 Only)
Your Jacuzzi spa incorporates a “Divert-A-Jet” or
“Massage Selector” (page 9) that allows you to custom-
ize massage performance between various jet systems
by diverting water between them. Simply turn the Divert-
A-Jet or Massage Selector to position A (Combo), B, or C
to divert water pressure to various jet groups. Note: The
valve is intended to operate in positions A (Combo), B,
and C for optimum performance. It is considered normal
for sound levels within the valve to vary between positions
due to the large amounts of water flowing through it! For
optimum filtration benefits, leave the valve in position A (center position)
when spa is covered. Select position B or C for maximum jet perfor-
mance during spa use.
Your Jacuzzi spa incorporates a “Divert-A-Jet” or
“Massage Selector” (page 9) that allows you to custom-
ize massage performance between various jet systems
by diverting water between them. Simply turn the Divert-
A-Jet or Massage Selector to position A (Combo), B, or C
to divert water pressure to various jet groups. Note: The
valve is intended to operate in positions A (Combo), B,
and C for optimum performance. It is considered normal
for sound levels within the valve to vary between positions
due to the large amounts of water flowing through it! For
optimum filtration benefits, leave the valve in position A (center position)
when spa is covered. Select position B or C for maximum jet perfor-
mance during spa use.
10.5 Adjusting Individual Jet Flow
The water flow to the individual jets in your spa can be
increased or decreased by rotating the outside jet face.
Note: Always keep at least 6 adjustable jets open at all times.
The water flow to the individual jets in your spa can be
increased or decreased by rotating the outside jet face.
Note: Always keep at least 6 adjustable jets open at all times.
10.6 Air Controls
Certain jet systems have their own air control. Each control
introduces air into the water lines that supply that specific jet
group. Simply turn the air control selection counterclockwise
to open or clockwise to close. To minimize heat loss, all air
controls should be closed when the spa is not in use.
Certain jet systems have their own air control. Each control
introduces air into the water lines that supply that specific jet
group. Simply turn the air control selection counterclockwise
to open or clockwise to close. To minimize heat loss, all air
controls should be closed when the spa is not in use.
11.0 Automatic Filtration Cycles
The control system activates a programmable “standard” or “economy”
filtration cycle to remove debris from your spa. These cycles use the
low speed pump, skimmer basket, and filter cartridge quickly clear
“skim” the water of debris and minimize their “bathtub ring” affect. Apart
from their filtration benefit, each mode also effects the operation of your
spa’s heater. Refer to sections . and .2 below for additional infor-
mation.
filtration cycle to remove debris from your spa. These cycles use the
low speed pump, skimmer basket, and filter cartridge quickly clear
“skim” the water of debris and minimize their “bathtub ring” affect. Apart
from their filtration benefit, each mode also effects the operation of your
spa’s heater. Refer to sections . and .2 below for additional infor-
mation.
11.1 Standard Filtration/Heating Modes (F1-F3)
Standard filtration/heating modes are typically selected by customers in
cold climates where heat up times are extended due to lower ambient
temperatures. In these modes, the water temperature is regulated by
the set temperature, low-speed pump, and heater which turns on as
needed. After the programmed set temperature is reached, the heater
and pump turn off, only to turn back on at the next programmed filtra-
tion/heating cycle or during a heat call.
Standard filtration/heating modes are typically selected by customers in
cold climates where heat up times are extended due to lower ambient
temperatures. In these modes, the water temperature is regulated by
the set temperature, low-speed pump, and heater which turns on as
needed. After the programmed set temperature is reached, the heater
and pump turn off, only to turn back on at the next programmed filtra-
tion/heating cycle or during a heat call.
A
C
B
A
b
C