Kenwood VR-8050 Manual Do Utilizador
17
EN
Preparing for surround sound
Speaker settings
To enable you to obtain optimum enjoyment from the receiver’s listening
modes, make sure to complete the speaker settings (Subwoofer, Front,
Center, Surround and Surround Back Speakers) as described below.
modes, make sure to complete the speaker settings (Subwoofer, Front,
Center, Surround and Surround Back Speakers) as described below.
SETUP
MULTI CONTROL
POWER RCVR
Setup
(Multi
%/ fi,
@/#)
POWER
ON/STANDBY
TUNER
1
Turn on the power to this receiver by pressing the POWER
ON/STANDBY key or POWER RCVR key.
ON/STANDBY key or POWER RCVR key.
2
For the remote control, press and hold the TUNER key for
more than 3 seconds to switch to receiver mode.
more than 3 seconds to switch to receiver mode.
3
Press the SETUP key to enter the SETUP mode.
The Surround Back Speaker and Subwoofer output selections are
displayed as follows:
displayed as follows:
1 SB/SW AMP SB : Surround Back/Subwoofer Speaker ter-
minal will output SB sound. Surround
Back pre out will have output from SBL
only.
Back pre out will have output from SBL
only.
2 SB/SW AMP SW : Surround Back/Subwoofer Speaker ter-
minal will output Subwoofer sound. Sur-
round Back pre out will have output from
SBL and SBR.
round Back pre out will have output from
SBL and SBR.
3 SB/SW AMP OFF : It is not advisable to use Surround Back/
Subwoofer speaker terminal for this se-
lection.
lection.
Use the MULTI CONTROL knob or Multi (
%/fi) keys to select the
speakers.
Press the SETUP key to proceed to the next SETUP selection.
Press the SETUP key to proceed to the next SETUP selection.
Use ∧
∧
∧
∧
∧/∨
∨
∨
∨
∨ keys or
@/ #keys for the following displays.
1 SP SETUP
2 TEST TONE
3 SP DISTANCE
4 LFE LEVEL
5 DISP MODE
6 EXIT
2 TEST TONE
3 SP DISTANCE
4 LFE LEVEL
5 DISP MODE
6 EXIT
The flow of the SETUP is as follows:
SP SETUP
TEST TONE
SP DISTANCE
EXIT
DISP MODE
LFE LEVEL
Front Left
Center
Front Right
Surround Right
Surround Back Right
Surround Back Left
Surround Left
Subwoofer
Display Selector
Display Listen
Subwoofer
Front
Center
Surround
Surround
Back
Subwoofer
Re-mix
T. TONE
MANUAL
T. TONE
AUTO
L
C
R
R
SR
SBR
SL
SBL
SW
L
C
R
SR
SBR
SBL
SL
SW
• If you have selected “SB/SW AMP SB”, “SBR”/”Surround Back
Right” and “SBL”/”Surround Back Left” are not appeared but
“SB”/”Surround Back” is appeared on the Display.
“SB”/”Surround Back” is appeared on the Display.
4
Select a speaker system.
1 Select the SP SETUP and press the SETUP key again so that
the subwoofer setting indication “SUBW ON” appears.
L
SL S
SB
SR
C
R
SP
MUTE
OPTICAL 6CH INPUT
COAXIAL
ANALOG
96kHzfs
CINEMA EQ.
ACTIVE EQ.
DSP MODE
DTS.
MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII
A B
CLIP
AUTO DETECT
THX
AUTO
RDS
RTY
RTY
MEMO
STEREO
TUNED
Surround EX
SW
LFE
2 Use the MULTI CONTROL knob or Multi (%/fi) keys to select
the appropriate subwoofer setting.
1 SUBW ON : Subwoofer setting mode to the receiver is
ON.
2 SUBW OFF : Subwoofer setting mode to the receiver is
OFF.
• The initial setting is “SUBW ON”.
• When the setting “SUBW OFF” is selected, the Front Sspeakers
• When the setting “SUBW OFF” is selected, the Front Sspeakers
are automatically set to “FRNT LARGE” and the procedure skips
to step
to step
6.
Before step
6, press the SETUP key to accept the setting.
• When Subwoofer output sound is required, select “FRNT
NORMAL”, or select both “FRNT LARGE” and “SW RE-MIX ON”.
• After setting SW (Subwoofer) from OFF to ON, SB/SW AMP setup
display will appear to enable you to re-select either SW or SB from
the Surround Back Speaker or Subwoofer terminal.
the Surround Back Speaker or Subwoofer terminal.
3 Press the ∧∧∧∧∧ key or # key to accept the setting.
• The front speakers setting indication “FRNT” appears.
L
SL S
SB
SR
C
R
SP
MUTE
OPTICAL 6CH INPUT
COAXIAL
ANALOG
96kHzfs
CINEMA EQ.
ACTIVE EQ.
DSP MODE
DTS.
MATRIX
DISCRETE
DOLBY DIGITAL
PRO LOGIC
STEREO
LOUDNESS
NEO:6
CSII
A B
CLIP
AUTO DETECT
THX
AUTO
RDS
RTY
RTY
MEMO
STEREO
TUNED
Surround EX
SW
LFE
4 Use the MULTI CONTROL knob or Multi (%/fi) keys to select
the appropriate front speakers setting.
1 FRNT NORMAL
: Average size Front Speakers are con-
nected to the receiver.
2 FRNT LARGE
: Large Front Speakers are connected
to the receiver.
• For “FRNT LARGE” selection, no sound will be heard from
Subwoofer speaker even when it is set to on. However, if you
select “SW RE-MIX ON” when Subwoofer is selected, you will
be able to hear sound from the Subwoofer.
When in STEREO mode, the sound goes directly to Front
Speaker.
select “SW RE-MIX ON” when Subwoofer is selected, you will
be able to hear sound from the Subwoofer.
When in STEREO mode, the sound goes directly to Front
Speaker.
5 Press the ∧∧∧∧∧ key or # key to accept the setting.
• The Center Speaker setting indication “CNTR” appears.
Continued to next page.
*5458/17-25/EN
04.3.5, 0:14 PM
17