halcro-logic dm10 Manual Do Utilizador
Page 23 of 29
TM
dm10
SPECIFICATIONS & FEATURES of the
HALCRO dm10
Remote Control Preamplifier
Inputs
§
§
3 RCA Unbalanced Voltage Mode
§
3 XLR Balanced Voltage Mode
§
1 RCA Current Mode
§
Any 5 of the above I/Ps are user
programmable to respond to the device
programmable to respond to the device
names; CD, DVD, Tape, Tuner, Aux1
§
1 RCA Unbalanced Phono
§
1 XLR Balanced Phono
§
Moving Coil or Moving Magnet
Cartridge
§
Variable
Phono
capacitance
and
resistance knobs
Outputs
§
§
2 Pair RCA Unbalanced Voltage Mode,
Bridgeable
§
2 Pair XLR Balanced Voltage Mode,
Bridgeable
§
2 Pair RCA Current Mode: 1 pair for un-
bridged connection, the other pair used
in bridged mode
in bridged mode
§
1 Pair RCA Tape output
§
¼ inch Stereo Headphone Jack
§
6-pin XLR power ON/OFF, pulsed and
level output control
Power supply
Switch-mode, >200kHz CW, 4th order mains
filter, 4th order supply rail filter. Fully
filter, 4th order supply rail filter. Fully
complies with EMC and CE standards.
Circuit contains extensive mains transient
Circuit contains extensive mains transient
protection and fault sensing protection.
Power consumption.
100W max via IEC input
Power consumption.
100W max via IEC input
Mains voltage.
85VAC to 240VAC at 40Hz to 200Hz or
120V to 340V D.C.
(Power supply will operate up to 270V but
120V to 340V D.C.
(Power supply will operate up to 270V but
IEC sockets only rated up to 240V by
regulatory authorities.)
regulatory authorities.)
Remote Control: 3 x AAA batteries
(supplied)
Dimensions
Ÿ
Width: 448mm, 17.64 inches
Ÿ
Depth: 400mm, 15.74 inches
Ÿ
Height: 240mm, 9.44 inches
Ÿ
Weight: 23kg, 49.6lbs
Shipping Dimensions
- Timber case
Ÿ
Width: 585mm, 23 inches
Ÿ
Depth: 535mm, 21 inches
Ÿ
Height: 515mm, 20 inches
Ÿ
Weight: 36 kg, 79 lbs
Remote Control dimensions
Ÿ
Ÿ
Length: 183mm, 7.2 inches
Ÿ
Width: 50mm, 1.96 inches
Ÿ
Thickness: 24mm, .94 inches
Ÿ
Weight: 280gm, .6 lbs
Gain
Un-balanced and balanced +20dB to -60dB
set by volume control.
set by volume control.
Phono 32dB, 38dB or 44dB for moving coil,
switch selectable
switch selectable
+27dB for moving magnet (measured at
1kHz)
Input impedance
1kHz)
Input impedance
Balanced; 10kohm + 10kohm
Un-balanced; 10kohm
Un-balanced; 10kohm
Moving magnet; 10kohm to 60kohm plus
60pF through to 350pF both continuously
60pF through to 350pF both continuously
variable
Moving coil; 220ohm plus 4.7nF
Moving coil; 220ohm plus 4.7nF
Current input mode; 50ohm
Output impedance
Output impedance
170 + 170ohms balanced and 170ohms
un-balanced
un-balanced
>30kohms current mode
10ohms headphones
340ohms tape
Distortion
Unmeasurable: below noise floor
10ohms headphones
340ohms tape
Distortion
Unmeasurable: below noise floor
At full specified output, < 250 parts per
billion (-132dB) for balanced and un-
billion (-132dB) for balanced and un-
balanced and current modes
Volume control
Volume control
+20dB to –60dB in 0.5dB steps.
Phono equalization
Phono equalization
Conforms to within +/-0.5dB of the RIAA
standard.
standard.