dls up6 Manual Do Utilizador
TWEETER INSTALLATION UR1
DLS Svenska AB
P.O. Box 13029
SE-40251 Göteborg, Sweden
Tel: +46 31 840060
Fax: +46 31 844021
E-mail: info@dls.se
www.dls.se
Technical Assistance
For technical assistance ask the shop where the product
was sold or the distributor in your very country.You can
always phone the DLS Helpdesk in Sweden + 46 31
840060 or send an e-mail to info@dls.e
Information can also be found on our WEB-site www.dls.se
We follow a policy of continuous advancement in
development. For this reason all or part of specifications
& designs may be changed without prior notice.
was sold or the distributor in your very country.You can
always phone the DLS Helpdesk in Sweden + 46 31
840060 or send an e-mail to info@dls.e
Information can also be found on our WEB-site www.dls.se
We follow a policy of continuous advancement in
development. For this reason all or part of specifications
& designs may be changed without prior notice.
WARRANTY SERVICE
This speaker is covered by warranty, depending on the
conditions in the country where it is sold. If the speaker is
returned for service, please include the original dated
receipt with the product.
conditions in the country where it is sold. If the speaker is
returned for service, please include the original dated
receipt with the product.
UR1 can be installed on the dashboard or recessed in a doorside.
These tweeters are included in the DLS ULTIMATE speaker kits UR5,
UR6, UR5S, UR6S, UR35S and UR36S.
These tweeters are included in the DLS ULTIMATE speaker kits UR5,
UR6, UR5S, UR6S, UR35S and UR36S.
SURFACE MOUNTING:
Use all accessories coming with the
tweeter. Attach the round bottom plate
(A) with the screws (B) or double
adhesive tape.
The fasten the round holder (C) to the
bottom plate using the screw and nut
(D). The tweeter element (G) is then
attached to the holder with three short
screws (E).
tweeter. Attach the round bottom plate
(A) with the screws (B) or double
adhesive tape.
The fasten the round holder (C) to the
bottom plate using the screw and nut
(D). The tweeter element (G) is then
attached to the holder with three short
screws (E).
TWEETER INSTALLATION UP1C
UP1C can be installed on the dashboard with the angled cup or
recessed in a doorside with the flush cup.
UP1C are included in the UP5, UP6, UP35 and UP36 speaker kits.
recessed in a doorside with the flush cup.
UP1C are included in the UP5, UP6, UP35 and UP36 speaker kits.
RECESSED MOUNTING:
You need a hole with a diameter of 48 mm
/ 1,89" in the door side. Put the two metal
wings through the two tracks in the center
of the cup, just as the picture shows, and
attach them with the M4 screw and nut
through the center hole. The cup is
attached to the door side when the metal
wings is pressed to the back side of the
door.
Put the tweeter element into the cup with
the cable going out through the bottom
hole. Then attach the element into the cup
and turn it clockwise to attach to the cup.
When removing the element from the cup,
turn it ccw and lift it out
/ 1,89" in the door side. Put the two metal
wings through the two tracks in the center
of the cup, just as the picture shows, and
attach them with the M4 screw and nut
through the center hole. The cup is
attached to the door side when the metal
wings is pressed to the back side of the
door.
Put the tweeter element into the cup with
the cable going out through the bottom
hole. Then attach the element into the cup
and turn it clockwise to attach to the cup.
When removing the element from the cup,
turn it ccw and lift it out
FACTS ABOUT DLS UR1 TWEETER
FACTS ABOUT DLS UP1C TWEETER
Size
28 mm / 1,1"
Nom. power (RMS)
50 Watts (80 Watts max)
Freq. range
1,5 kHz-20 kHz
Sensitivity
93 dB
Magnet diameter
28 mm / 1,1"
Mounting depth
18 mm / 0,71"
Mounting hole
48 mm / 1,89"
Cone material
Hand treated fabric
SURFACE
MOUNTING:
MOUNTING:
For angled surface mount
together with the angled cup:
The tweeter element is
attached to the cup by fitting
the three wings on the angled
cup into the tracks of the ele-
ment and then turn it
clockwise. When removing the
element from the cup, turn it
ccw and lift it up.
together with the angled cup:
The tweeter element is
attached to the cup by fitting
the three wings on the angled
cup into the tracks of the ele-
ment and then turn it
clockwise. When removing the
element from the cup, turn it
ccw and lift it up.
A
B
D
C
E
F
G
RECESSED MOUNTING:
You need a hole with a diameter of 45 mm / 1,77" in the door side.
Attach the tweeter element (G) to the door side with the round holder
(C) on the back side of the door panel. Use the three long screws (F)
to attach the element to the holder.
Attach the tweeter element (G) to the door side with the round holder
(C) on the back side of the door panel. Use the three long screws (F)
to attach the element to the holder.
Art.no
10-25401
Size
28 mm
Nom. power (RMS)
50 Watts (80 Watts max)
Freq. range
1 kHz-25 kHz
Sensitivity
93 dB
Fs
900 Hz
Overall dimensions
62 mm / 2,44"
Magnet
28 mm / 1,1" neodymium
Mounting depth
26 mm / 1"
Mounting hole
45 mm / 1,77"
Cone material
Hand treated fabric