Carvin 822 Manual Do Utilizador
SPEAKER CABLES
The PH50 is our standard cable when purchasing a complete sound system.
These cables feature 1/4” plugs and heavy 16 gauge copper wire. The PH50 is
adequate for lengths up to 50’ under normal use. You can DAISY-CHAIN up to one
additional speaker per cable by using the unused 1/4” OUTPUT” jack (right side)
on your speaker jack plate. Be sure to note the total impedance to the amp so it is
not lower than it’s recommended impedance. See
adequate for lengths up to 50’ under normal use. You can DAISY-CHAIN up to one
additional speaker per cable by using the unused 1/4” OUTPUT” jack (right side)
on your speaker jack plate. Be sure to note the total impedance to the amp so it is
not lower than it’s recommended impedance. See
Typical Loudspeaker Impedance
Configurations.
PRECAUTIONS
1) DO NOT EXCEED THE POWER RATING marked on the rear connect plate.
Excessive power will destroy drivers. 2) DISTORTION from power amps will destroy
drivers much faster than clean power. 3) WATER, MOISTURE, and DUST are
harmful to drivers causing failure which is not covered under warranty.
drivers much faster than clean power. 3) WATER, MOISTURE, and DUST are
harmful to drivers causing failure which is not covered under warranty.
WARRANTY
CARVIN loudspeakers are covered by a ONE year limited warranty unless
otherwise stated. Warranty coverage is limited to original manufactures defects
only. WARRANTY DOES NOT COVER: 1) Opened or burned voice coils. 2) Torn
cones caused by improper packing or abuse. 3) Damage from rain, moisture, ETC.
When returning defective driver(s), remove them from the enclosure to reduce
shipping costs . DO NOT stuff paper into the driver(s). Return pre-paid by UPS.
Include your address and description of the problem. Your driver(s) will be returned
COD for the cost of shipping and reconditioning if not covered under warranty.
only. WARRANTY DOES NOT COVER: 1) Opened or burned voice coils. 2) Torn
cones caused by improper packing or abuse. 3) Damage from rain, moisture, ETC.
When returning defective driver(s), remove them from the enclosure to reduce
shipping costs . DO NOT stuff paper into the driver(s). Return pre-paid by UPS.
Include your address and description of the problem. Your driver(s) will be returned
COD for the cost of shipping and reconditioning if not covered under warranty.
MODEL 822 SPEAKER SYSTEM SPECS:
Frequency Response:
80 Hz to 16 kHz ±3 dB
Useable Low Frequency:
50 Hz (-10 dB)
Power Handling:
300 watts Continuous Power
Recommended Amp:
50 to 300 watts
Sensitivity:
99 dB SPL
Coverage Angles:
90° Horizontal, 45° Vertical
Nominal Impedance:
8
Ω
Horn Driver Protection:
Yes
Connectors:
One input & one output 1/4" phone connector
Woofer Enclosure Type:
Computer Optimized Vented Box
Enclosure Covering:
Duratuff II™
Dimensions:
17.5"W x 12"D x 22"H
Net Weight:
31 lbs.
Warranty:
One Year
Options:
Cover: CVS822, Stand: SS20
or
SS30
822 FREQUENCY RESPONSE
CARVIN ENGINEERING DATA
822 SPEAKER SYSTEM
INSTRUCTIONS
822
Congratulations on your selection of the 822 12“ 2-way loudspeaker. The 822 is
ideal for use in small clubs or halls as a sound reinforcement loudspeaker. The 822
includes a built-in recessed bracket for the convenience of adding a speaker stand.
With 300 watt power handling, the 822 is an excellent choice when portability and
performance are of equal importance.
includes a built-in recessed bracket for the convenience of adding a speaker stand.
With 300 watt power handling, the 822 is an excellent choice when portability and
performance are of equal importance.
RECEIVING INSPECTION
INSPECT YOUR SPEAKER FOR ANY DAMAGE which may have occurred during
shipping. If any damage is found, please notify the shipping company & CARVIN.
SAVE THE CARTON & ALL PACKING MATERIALS. In the event you have to re-ship
your unit, always use the original carton and packing material. This will provide the best
possible protection during shipment. CARVIN and the shipping company are not liable
for any damage caused by improper packing.
possible protection during shipment. CARVIN and the shipping company are not liable
for any damage caused by improper packing.
SAVE YOUR INVOICE. It will be required for warranty service if needed in the future.
SHIPMENT SHORTAGE. If you find items missing, they may have been shipped
separately. Please allow several days for the rest of your order to arrive before inquiring.
RECORD THE SERIAL NUMBER on the enclosed warranty card or below on this
manual for your records. Keep your portion of the card and return the portion with your
name and comments to us.
name and comments to us.
SUGGESTIONS FOR OPTIMAL PERFORMANCE
Raise the enclosure to the ear level of your audience for greater coverage. To
help control feedback, use a graphic equalizer. Keep the speakers in front of the
microphone. Never direct the microphone towards the speaker. For greater
coverage, add a second speaker system 20° to 30° off axis.
microphone. Never direct the microphone towards the speaker. For greater
coverage, add a second speaker system 20° to 30° off axis.
TYPICAL LOUDSPEAKER IMPEDANCE CONFIGURATIONS
Individual speaker or speaker cabinet wiring examples for total impedance.
For your records, you may wish to record the following information.
Serial No._____________________ Invoice Date_______________
SERIES CONNECTION
16
Ω
TOTAL IMPEDANCE
+
+
+
PARALLEL CONNECTION
4
Ω
TOTAL IMPEDANCE
+
+
+
8
Ω
TOTAL
IMPEDANCE
SERIES/PARALLEL
CONNECTION
8
Ω
TOTAL IMPEDANCE
+
+
+
+
+
+
+
8
Ω
8
Ω
8
Ω
8
Ω
8
Ω
8
Ω
8
Ω
4
Ω
8
Ω
8
Ω
16
Ω
8
Ω
8
Ω
REAR CONNECT PLATE
Two professional twist-lock SPEAKON™
connectors and two standard 1/4” phone
jacks are featured. Use these connectors
for connecting to the power amp and daisy
chaining to an additional speakers.
jacks are featured. Use these connectors
for connecting to the power amp and daisy
chaining to an additional speakers.
12340 World Trade Drive, San Diego, CA 92128
(619) 487-1600 (800) 854-2235
www.carvin.com